Hi --

I recently installed R5A12 on my 7NIF2.. for some reason the on board sound card isn't being recognized.. checked the wiki but it's not clear how to setup sound in R5...

Adrian



adrianbc@mythtv:~$ dmesg
Linux version 2.6.9-chw-4 (root@dev.mysettopbox.tv) (gcc version 3.3.4 (Debian 1:3.3.4-9)) #1 SMP Fri Feb 4 20:15:03 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dff0000 (usable)
BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS)
BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
On node 0 totalpages: 122864
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 118768 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f6ea0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff7740
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:4 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=Linux ro root=301 apm=power-off nomce
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1336.426 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 481796k/491456k available (2769k kernel code, 9124k reserved, 1040k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2646.01 BogoMIPS (lpj=1323008)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) processor stepping 04
per-CPU timeslice cutoff: 731.60 usecs.
task migration cache decay timeout: 1 msecs.
Total of 1 processors activated (2646.01 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ... works.
Brought up 1 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbee0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbf10, dseg 0xf0000
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 23 (level, high) -> IRQ 23
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 22
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, high) -> IRQ 21
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 20 (level, high) -> IRQ 20
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 22 (level, high) -> IRQ 22
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 18 (level, high) -> IRQ 18
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, high) -> IRQ 16
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
SELinux: Registering netfilter hooks
Initializing Cryptographic API
vesafb: framebuffer at 0xc4000000, mapped to 0xde880000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d710
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.4-2004/02/19-spock-0.1: looking for picture... no good signature found.
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD2000JB-00GVA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA CD-ROM XM-6702B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 1024KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
libata version 1.02 loaded.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices:
SLPB HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... <6>kjournald starting. Commit interval 5 seconds
okay
Freeing unused kernel memory: 196k freed
Adding 891596k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 22
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 22, pci mem de86a000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, high) -> IRQ 21
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 21, pci mem de86c000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
usb 1-1: new low speed USB device using address 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver hiddev
ts: Compaq touchscreen protocol output
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
Real Time Clock Driver v1.12
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (1 C)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: AGP aperture is 512M @ 0xa0000000
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.29.
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 010de:0c11 bound to 0000:00:04.0
NET: Registered protocol family 17
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Disabled Privacy Extensions on device c0465bc0(lo)
eth0: no link during initialization.
eth0: link up.
Linux video capture interface: v1.00
tuner: Ignoring new-style parameters in presence of obsolete ones
ivtv: Unknown parameter `debug'
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3a) loading
ivtv: Linux version: 2.6.9-chw-4 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 18 (level, high) -> IRQ 18
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) by insmod option
tuner: The type=<n> insmod option will go away soon.
tuner: Please use the tuner=<n> option provided by
tuner: tv aard core driver (bttv, saa7134, ...) instead.
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Feb 5 2005 20:42:28
ivtv: i2c attach [client=MSP3448W-A2,ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x48, (1F) 0xc0
tveeprom: Hauppauge: model = 32032, rev = B310, serial# = 7043549
tveeprom: tuner = Philips FI1236 MK2 (idx = 10, type = 2)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3440 (type = 11)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 2, Tuner formats 0x00001000, Radio: yes, Model 0x00893450, Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 2
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: ivtv_enc_thread: pid = 2176, itv = 0xdeee2920
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ==================== END INIT IVTV ====================
saa7115: decoder disable output
saa7115: decoder set input (0)
saa7115: now setting Composite input
ivtv: Setting audio matrix to input 1, output 1
saa7115: decoder enable output
saa7115: decoder set size
eth0: no IPv6 routers present
saa7115: decoder disable output
saa7115: decoder set input (4)
saa7115: now setting Composite input
ivtv: Setting audio matrix to input 3, output 1
saa7115: decoder enable output
saa7115: decoder set picture bright=128 contrast=63 saturation=64 hue=0
saa7115: decoder set picture bright=128 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder set picture bright=127 contrast=63 saturation=63 hue=0
saa7115: decoder disable output
input: PC Speaker
saa7115: decoder enable output
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 20 (level, high) -> IRQ 20
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 20, pci mem dec94000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 1-1: USB disconnect, address 2
ohci_hcd 0000:00:02.0: wakeup
usb 1-1: new low speed USB device using address 3
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, high) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:02:00.0 into 4x mode

FYI I also update asla-utils alsa-base and ran alsa_init

However, I am still unable to run alsamixer as the sound card is not properly configured. I am just trying to use the built in AC'97 on the 7NIF2

did you try alsa-autoconfig? i think it's under /etc/init.d
see if that helps. also what is your cat /proc/asound/pcm and /proc/asound/devices look like?

thanks i just tried ./also-autoconfig...

root@mythtv:/etc/init.d# ./alsa-autoconfig
Building card database..
root@mythtv:/etc/init.d#

but nothing changed as far as I can tell.

here is a print out of pcm and devices...

root@mythtv:/etc/init.d# cat /proc/asound/pcm
root@mythtv:/etc/init.d# cat /proc/asound/devices
33: : timer
root@mythtv:/etc/init.d#

did you check your BIOS to make sure you did not disable the onboard sound?

try alsaconf

_________________
Have a question search the forum and have a look at the KnoppMythWiki.

Xsecrets

Thanks the problem was that AC'97 was disabled in the bios. Once I restarted I ran alsa_conf and alsa_init then restarted. Then I adjusted the levels in the alsamixer