View unanswered posts    View active topics

All times are UTC - 6 hours





Post new topic Reply to topic  [ 7 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
PostPosted: Sat Oct 21, 2006 12:37 am 
Offline
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
Well I went and bought a PVR-150, with remote.

MythTV runs and everything but when I go into View TV, all I get is static and snow sound.

I've tried using all 4 of the cable frequences settings. I don't know what I'm doing wrong yet.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Oct 21, 2006 1:28 am 
Offline
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
Wow this stuff is confusing! lol


Top
 Profile  
 
 Post subject:
PostPosted: Sat Oct 21, 2006 2:11 am 
Offline
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
I put the card into a Windows PC, it works fine in windows, but didn't give me the option to select what frequency I wanted to use, and also doesn't tell me.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Oct 21, 2006 9:15 am 
Offline
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location: Arlington, MA
This is what happens when you do this kind of stuff at 0-dark-30, all the brain cells with the facts that you already knew have gone to bed without you. ;-) Once you've had 8 hours of sleep I'm sure you'll remember that we pre-pointed you to the troubleshooting pages on the wiki for exactly this issue. http://mysettopbox.tv/phpBB2/viewtopic.php?t=12143&postdays=0&postorder=asc&start=14 (hint, hint, ...) ;-)

Also see:
http://www.knoppmythwiki.org/index.php?page=TroubleShooting (bookmartk this)
http://www.knoppmythwiki.org/index.php?page=BlackScreenWatchingTV
http://www.knoppmythwiki.org/index.php?page=CheckingLogFiles
http://www.knoppmythwiki.org/index.php?page=TVCaptureCards

BTW - Since Cecil considers this type of thing a post install configuration this this thread may disappear very quickly...


Top
 Profile  
 
 Post subject:
PostPosted: Sat Oct 21, 2006 12:59 pm 
Offline
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
Thank you tjc. I'll go through these and see what I can come up with.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Oct 21, 2006 1:37 pm 
Offline
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
Output from sed -n '/= START INIT IVTV/,/= END INIT IVTV/p' </var/log/messages | more

Code:
mythtv kernel: ivtv:  ==================== START INIT IVTV ====================
mythtv kernel: ivtv:  version 0.7.0 (tagged release) loading
mythtv kernel: ivtv:  Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4
mythtv kernel: ivtv:  In case of problems please include the debug info between
mythtv kernel: ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
mythtv kernel: ivtv:  any module options, when mailing the ivtv-users mailinglist.
mythtv kernel: ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
mythtv kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
mythtv kernel: ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
mythtv kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
mythtv kernel: tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
mythtv kernel: cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
mythtv kernel: cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
mythtv kernel: wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
mythtv kernel: tveeprom 0-0050: Hauppauge model 26152, rev E5B2, serial# 9733113
mythtv kernel: tveeprom 0-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
mythtv kernel: tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
mythtv kernel: tveeprom 0-0050: audio processor is CX25843 (idx 37)
mythtv kernel: tveeprom 0-0050: decoder processor is CX25843 (idx 30)
mythtv kernel: tveeprom 0-0050: has no radio, has IR remote
mythtv kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
mythtv kernel: ivtv0: Encoder revision: 0x02050032
mythtv kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
mythtv kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
mythtv kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
mythtv kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
mythtv kernel: tuner 0-0061: tuner type not set
mythtv kernel: tuner 0-0061: tuner type not set
mythtv kernel: ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
mythtv kernel: ivtv:  ====================  END INIT IVTV  ====================


Looks like I have the "old tuner type not set" issue, and this page should help me: http://www.knoppmythwiki.org/index.php? ... ptureCards


Top
 Profile  
 
 Post subject:
PostPosted: Sat Oct 21, 2006 1:48 pm 
Offline
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
Thank you again tjc. It's working perfect now. All I needed was someone to point me in the right direction.


Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 


All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu