Author |
Message |
RacerX
|
Posted: Wed Sep 12, 2007 2:11 pm |
|
Joined: Sun Sep 05, 2004 7:06 pm
Posts: 690
|
Last night I upgraded my main box from R5E50 to R5F27. The installation went fine but when I rebooted the system lilo came up with the error
"Loading LinuxEBDA is big; kernel setup stack overlaps LILO second stage. "
So I searched the forum and found this post
http://mysettopbox.tv/phpBB2/viewtopic. ... =linuxebda
So I thought why not boot the cd and see what's up
Following Cesman's post
Code: mount - rw /dev/hda1 /mnt/hda1 chroot /mnt/hda1 then ran lilo -v But the same error came up. Next, I checked the size of the files in the /boot directory on the drive but they were exactly the same size as the ones on the cd. At this time I thought it wise to get some sleep. When I booted the system this morning I get a "Eminent Smart Drive Failure Error." This made me quite uneasy but I read from TJC's post the patience is important. So I opened up the case replaced the ide cable and set the jumper on master. When I booted the system it came up so I went thru the migration. At this point I realized that something was wrong because the backend would not come up even thought I had the nic working with the weather. Hmm so that made me think maybe something with wrong with the upgrade so I ran the knoppmyth Restore. It started but it only ran for 30 seconds so I knew it it did not work. So I did some more googling on commands and came up with Code: cat /proc/partitions that showed me that my partitions were intact so that was a big releaf. Next I booted the cd and looked at the partition info. It told me that the swap partition had no lablel and that /myth partition was EXT3. I tried to mount the swap partition but it failed Code: mount -t ext3 /dev/hda2 /swap it did work with Code: mount -t ext3 /dev/hda3 /myth
I used Xedit and I can now see all my shows in /myth/tv and /myth/pretty
At startup the system mounted
/dev/hda1 /boot
but I also need
/dev/hda2/ /swap
/dev/hda3/ /myth
So I decided that this is where I need a little assitance. What exactly is the rule of thumb in regards to the mount points and making them permanent at startup when they do not happen automatically??? Moreovever, what needs to happen with the database since the upgrade is done but it did not upgrade my schema since the partition was not mounted? Feels like the twilight zone...
Last edited by RacerX on Wed Sep 12, 2007 7:30 pm, edited 1 time in total.
|
|
Top |
|
|
slowtolearn
|
Posted: Wed Sep 12, 2007 2:22 pm |
|
Joined: Wed Nov 16, 2005 8:55 pm
Posts: 1381
Location:
Farmington, MI USA
|
What is the contents of your /etc/fstab?
|
|
Top |
|
|
RacerX
|
Posted: Wed Sep 12, 2007 2:41 pm |
|
Joined: Sun Sep 05, 2004 7:06 pm
Posts: 690
|
As requested
# /etc/fstab: filesystem table.
#
# filesystem mountpoint type options dump pass
/dev/hda1 / ext3 defaults,errors=remount-ro 0 1
/dev/hda3 /dev/hda3 auto defaults,auto 0 2
proc /proc proc defaults 0 0
/dev/fd0 /floppy vfat defaults,user,noauto,showexec,umask=022 0 0
usbfs /proc/bus/usb usbfs devmode=0666 0 0
sysfs /sys sysfs defaults 0 0
tmpfs /dev/shm tmpfs defaults 0 0
/dev/cdrom /cdrom auto defaults,ro,user,noexec,noauto 0 0
# Added by KNOPPIX
/dev/hda2 none swap defaults 0 0
|
|
Top |
|
|
mihanson
|
Posted: Wed Sep 12, 2007 2:50 pm |
|
Joined: Sun Sep 25, 2005 3:50 pm
Posts: 1013
Location:
Los Angeles
|
RacerX wrote: /dev/hda3 /dev/hda3 auto defaults,auto 0 2
I believe your 2nd reference to /dev/hda3 in this line should be /myth
_________________ Mike
My Hardware Profile
|
|
Top |
|
|
mythedoff
|
Posted: Wed Sep 12, 2007 2:57 pm |
|
Joined: Mon Jul 31, 2006 10:41 pm
Posts: 149
|
# /etc/fstab: filesystem table.
#
# filesystem mountpoint type options dump pass
...
/dev/hda3 /dev/hda3 auto defaults,auto 0 2
...
Mine shows:
/dev/hda3 /myth ext3 defaults,auto 0 2
Perhaps that would work.
|
|
Top |
|
|
RacerX
|
Posted: Wed Sep 12, 2007 3:01 pm |
|
Joined: Sun Sep 05, 2004 7:06 pm
Posts: 690
|
Hello
"/dev/hda3 /myth ext3 defaults,auto 0 2 "
Looks good to me, but what does it say for?
/dev/hda2
Thanks for helping
|
|
Top |
|
|
jmckeown2
|
Posted: Wed Sep 12, 2007 3:22 pm |
|
Joined: Sat Sep 02, 2006 9:17 am
Posts: 359
|
RacerX wrote: Looks good to me, but what does it say for?
/dev/hda2
Code: /dev/hda2 none swap defaults 0 0 Your mount command above wouldn't have worked, because swap space doesn't get mounted like other filesystems. -- if you were to do it by hand you would use the swapon command. If you're not sure if your swap is active use Code: cat /proc/swaps
|
|
Top |
|
|
RacerX
|
Posted: Wed Sep 12, 2007 3:57 pm |
|
Joined: Sun Sep 05, 2004 7:06 pm
Posts: 690
|
You are correct I checked
Code: cat /proc/swaps
and it shows the swapfile on hda2
Thanks
I also made the change to
/etc/fstab
and that makes the correction for the mount points
Now what about the upgrade since my schema was not migrated what is the best way to sync up the system. Any thoughts on that one?
|
|
Top |
|
|
slowtolearn
|
Posted: Wed Sep 12, 2007 4:37 pm |
|
Joined: Wed Nov 16, 2005 8:55 pm
Posts: 1381
Location:
Farmington, MI USA
|
RacerX wrote: Now what about the upgrade since my schema was not migrated what is the best way to sync up the system. Any thoughts on that one? Did the system bootup as expected? If so, I would:
* - Check /var/log/mythtv/mythbackend.log - If you find a bunch of lines that say "Upgrading to schema version XXXX" then I would guess your system is upgraded. If not then
* - Assuming you still have your backup in /myth/backup (double-check), you could simply perform another upgrade.
|
|
Top |
|
|
RacerX
|
Posted: Wed Sep 12, 2007 5:57 pm |
|
Joined: Sun Sep 05, 2004 7:06 pm
Posts: 690
|
Yes, the system booted up just fine with the change to FSTAB.
However, the schema change ran this morning before I fixed that
problem.
So right now when I run mythtv-setup for example it shows schedules direct setup page. But I need to run part or all of the upgrade to update my schema and any other config setttings that it ran so that mythbackend starts to see my data. It is not clear to me what is the best course of action in this case since the ungrade is only partially compleated. I have three choices, mythtv restore, mythtv upgrade, or mythtv partial upgrade. I need some more info in order to choose the correct path.
|
|
Top |
|
|
tjc
|
Posted: Wed Sep 12, 2007 6:48 pm |
|
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location:
Arlington, MA
|
Unless you've made recordings in the meantime just redo the upgrade or run the restore script then reboot.
|
|
Top |
|
|
RacerX
|
Posted: Wed Sep 12, 2007 7:29 pm |
|
Joined: Sun Sep 05, 2004 7:06 pm
Posts: 690
|
I reran the update to R5F27 and everything worked fine. Everything is back to normal
THANKS to everyone who helped
Problem Solved
|
|
Top |
|
|