I can't get my silver pvr-250 remote (Non A415-HPG) to work with a fresh install of R6 "6.00.08".
I looked at the bug report [url]http://linhes.org/flyspray/index.php?do=details&task_id=403&project=2&status[0]=open&pagenum=2[/url] in flyspray FS#403.
In the linhes setup I used both the hauppauge-silver remote setup and the gray remote and neither work. I can get commands out with raw but I only get outputs with IRW when I configure it as a gray remote. when I select what I think is the correct setup in the linhes setup menu (silver remote), I do not get anything out with IRW. Regardless, both setting results with zero control with a remote.
I don't know where to go from here using R6.
This is what I have done so far to troubleshoot:
Quote:
Stoped Lirc
[root@mythtv etc]# sudo sv stop lircd
[root@mythtv etc]# mode2 -r (Then pressed the up down on rmt)
code: 0x1795
code: 0x1f94
code: 0x1f94
code: 0x1f94
_____________________________________________
[root@mythtv etc]# cat lircd.conf
include "/usr/MythVantage/templates/remotes/hauppauge-grey-g3/lircd-haupgrey-g3.conf"
I get from irw
[root@mythtv etc]# irw
0000000000001795 00 Down Hauppauge_350
0000000000001795 01 Down Hauppauge_350
0000000000001795 00 Down Hauppauge_350
0000000000001795 01 Down Hauppauge_350
0000000000001794 00 Up Hauppauge_350
0000000000001794 01 Up Hauppauge_350
__________________________________________
[root@mythtv etc]# cat lircd.conf
include "/usr/MythVantage/templates/remotes/hauppauge-silver/lircd-haupgrey.conf"
I get from irw
[root@mythtv etc]# irw
^C
__________________________________________
grep lirc /var/log/lircd (with gray remote in linhes menu)
[root@mythtv etc]# grep lirc /var/log/lircd
Jun 30 12:35:57 mythtv lircd: accepted new client on /dev/lircd
Jun 30 12:36:07 mythtv lircd: removed client
Jun 30 12:36:16 mythtv lircd: accepted new client on /dev/lircd
Jun 30 12:36:27 mythtv lircd: caught signal
Jun 30 12:36:32 mythtv lircd: lircd(default) ready
Jun 30 12:36:33 mythtv lircd: closing logfile
Jun 30 12:36:33 mythtv lircd: reopened logfile
grep lirc /var/log/lircd (then installed the silver remote in linhes menu)
[root@mythtv etc]# grep lirc /var/log/lircd
Jun 30 12:35:57 mythtv lircd: accepted new client on /dev/lircd
Jun 30 12:36:07 mythtv lircd: removed client
Jun 30 12:36:16 mythtv lircd: accepted new client on /dev/lircd
Jun 30 12:36:27 mythtv lircd: caught signal
Jun 30 12:36:32 mythtv lircd: lircd(default) ready
Jun 30 12:36:33 mythtv lircd: closing logfile
Jun 30 12:36:33 mythtv lircd: reopened logfile
Jun 30 12:38:43 mythtv lircd: accepted new client on /dev/lircd
Jun 30 12:38:50 mythtv lircd: removed client
Jun 30 12:38:51 mythtv lircd: accepted new client on /dev/lircd
Jun 30 12:39:00 mythtv lircd: caught signal
Jun 30 12:39:05 mythtv lircd: lircd(default) ready
Jun 30 12:39:06 mythtv lircd: closing logfile
Jun 30 12:39:06 mythtv lircd: reopened logfile
___________________________________________________
[root@mythtv etc]# grep lirc /var/log/messages.log
Jun 30 10:21:51 mythtv lirc_dev: IR Remote Control driver registered, major 61
Jun 30 10:21:51 mythtv lirc_i2c: chip 0x10020 found @ 0x18 (Hauppauge IR)
Jun 30 10:21:51 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10
Jun 30 11:16:35 mythtv lirc_i2c: chip 0x10020 found @ 0x18 (Hauppauge IR)
Jun 30 11:16:35 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10
Jun 30 11:16:36 mythtv lirc_dev: IR Remote Control driver registered, major 61
Jun 30 11:16:36 mythtv lirc_i2c: chip 0x10020 found @ 0x18 (Hauppauge IR)
Jun 30 11:16:36 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10
Jun 30 11:23:02 mythtv lirc_i2c: chip 0x10020 found @ 0x18 (Hauppauge IR)
Jun 30 11:23:02 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10
Jun 30 11:23:02 mythtv lirc_dev: IR Remote Control driver registered, major 61
Jun 30 11:23:02 mythtv lirc_i2c: chip 0x10020 found @ 0x18 (Hauppauge IR)
Jun 30 11:23:02 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10