LinHES Forums http://forums.linhes.org/ |
|
R6 SBE install breaks MBE http://forums.linhes.org/viewtopic.php?f=1&t=20507 |
Page 1 of 1 |
Author: | lusid [ Tue Nov 10, 2009 11:28 pm ] |
Post subject: | R6 SBE install breaks MBE |
I've had my R6 MBE running for a couple of months now, along with a frontend only install, with an HDHR and a central NFS share for recordings. Today I finally got around to installing an R6 SBE, and the results were pretty ugly. During install I picked SBE as the system type, assigned a unique hostname, and the installer found my MBE and the NFS share. Everything seemed fine. It launched myth setup after first boot, I looked through the screens and aside from it wanting to reconfigure my HDHR tuners on the SBE everything seemed fine. I could play my existing recording, but had no livetv. I didn't have time to work through it so I shut it down. Then I went back to my frontend only install, started it up, and it had lost all of its settings. I moved to the master backend, it too had lost all of its settings. I reconfigured the front end settings, got back into the FE install only to discover livetv no longer worked there either. I went into myth setup, and had no tuners. I had to reconfigure the HDHR on the MBE. I thought I had done something wrong, so I repeated the excercise on another machine. Built a SBE, and had the same issues again. So I double checked the system type on the SBE, and it was set to MASTER backend. I check the system type on the front end, which now thought it was STANDALONE. Am I missing some important step setting up an SBE? How do you configure an SBE without killing the MBE? |
Author: | jams [ Thu Nov 12, 2009 10:13 pm ] |
Post subject: | |
This shouldn't have happened, adding an SBE hasn't been tested in a while but it all worked last time I looked. I will take a look at this, but just to clarify this is your setup. 1) ONE MBE without FE 2) FE only 3) SBE without FE |
Author: | Too Many Secrets [ Fri Nov 13, 2009 6:18 pm ] |
Post subject: | |
I've seen this as well. Just figured I borked it on my own. MBE/FE and SBE/FE (with NFS). It came when I lost a HDD and had to reinstall SBE. database got skewed and ip addresses ended up backwards. I had to power off the SBE to get into the MBE from LinHES config. It wanted to go to the wrong BE. Very frustrating at 1am, but I am still not convinced it wasn't sumthin' I dun... |
Author: | lusid [ Fri Nov 13, 2009 10:02 pm ] |
Post subject: | |
My setup was: One MBE with FE, and One FE. Then I tried to add an SBE. By the end my system was fully roached. I ended up killing the SBE, backing up the recording related tables, restoring the MBE from a 2 week old snapshot, flushed the old tables, reimported the current tables, and ran a commflag rebuild. I still have issues with playing back some of my recordings over UPNP because the hostname of the recording owner in the recording tables is inconsistent, but I think I can patch that up in SQL. I think I'll hold off for a .22 release and a free weekend before I attempt this again. |
Author: | dfdario [ Wed Jun 09, 2010 5:17 am ] |
Post subject: | |
Since I am having the same problem, did you sove it? I fresh installed 6.03 MBE/FE and all working properly. When I try to add an SBE/FE I experience the same issue as above. It also happened me with 6.02. Any suggestion? |
Author: | dfdario [ Thu Jun 10, 2010 12:00 am ] |
Post subject: | |
>>>> Moved to LinHES installation >>>> http://mysettopbox.tv/phpBB2/viewtopic.php?t=21118 |
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |