LinHES Forums http://forums.linhes.org/ |
|
installed knoppmyth with aver 771 installed but cant watch t http://forums.linhes.org/viewtopic.php?f=1&t=5356 |
Page 1 of 1 |
Author: | phillbrett68 [ Thu Jul 14, 2005 10:50 pm ] |
Post subject: | installed knoppmyth with aver 771 installed but cant watch t |
hi list i have installed knoppmyth with an aver 771 card installed it goes through the everything fine i go into the mythtv-setup and i find my dvb card their fine i select it i scan for the channels yep i get them i creat a source fine i go through the who;e setup fine everything appears ok i get out and i run mythtv and all i get is a black scren nothing else ok after about 30 seconds it goes back to the main window does anyone know what might be wrong at all any help would be most appreciated thanks list signed phillip cole phillip cole phillbrett68@optusnet.com.au |
Author: | Greg Frost [ Fri Jul 15, 2005 12:57 am ] |
Post subject: | |
Dude this has been covered so many times. Go back into mythtv-setup and enter a valid starting channel in the Input Connections bubble. |
Author: | phillbrett68 [ Fri Jul 15, 2005 1:30 am ] |
Post subject: | installed knoppmyth with aver 771 installed but cant watch t |
hi greg thanks for the suggestion but this makes absolutey no fiference at all i put a valid channel that is in the list of my channels but still nothing ok thanks for your advice anyway ok bye signed phillip cole |
Author: | Xsecrets [ Fri Jul 15, 2005 10:48 am ] |
Post subject: | |
well just cause it's in the list doesn't actually mean it's valid, it is quite possible to get channels that are strong enough to get picked up on the scan, but not playback, for playback they have to come in at over 60% signal strength for a short time before myth will even attempt to playback on that channel. |
Author: | Bad-Taste [ Sat Jul 16, 2005 3:47 pm ] |
Post subject: | |
I have a big problem with this Card. when i install knoppmyth, modprobe the first time and added dvb-bt8xx into /etc/modules the Card works great. But when i restart my PC the Card cant be detected dmesg output: bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:00:0f.0, irq: 5, latency: 32, mmio: 0xeb000000 bttv0: detected: AVermedia AverTV DVB-T 771 [card=123], PCI subsystem ID is 1461 :0771 bttv0: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00fdff4f [init] bttv0: using tuner=4 bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bttv0: add subdevice "remote0" bttv0: add subdevice "dvb0" 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:00:0b.0: 3Com PCI 3c905 Boomerang 100baseTx at 0xd800. Vers LK1.1.19 eth0: Dropping NETIF_F_SG since no checksum feature. NET: Registered protocol family 17 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). bt878(0): Bt878 (rev 17) at 00:0f.1, irq: 5, latency: 32, memory: 0xeb001000 DVB: registering new adapter (bttv0). mt352_read_register: readreg error (reg=127, ret==-5) dvb-bt8xx: A frontend driver was not found for device 109e/0878 subsystem 1461/0 771 'Now, when i halt my machine and take the Avermedia in an other PCI Slot it will be detected, but after the next restart not more. That really sucks ![]() lspci -v: 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333] Flags: bus master, medium devsel, latency 0 Memory at e0000000 (32-bit, prefetchable) [size=128M] Capabilities: [a0] AGP version 2.0 Capabilities: [c0] Power Management version 2 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP] (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: e8000000-e9ffffff Prefetchable memory behind bridge: c0000000-dfffffff Capabilities: [80] Power Management version 2 0000:00:08.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 04) Subsystem: Creative Labs CT4850 SBLive! Value Flags: bus master, medium devsel, latency 32, IRQ 10 I/O ports at d000 [size=32] Capabilities: [dc] Power Management version 1 0000:00:08.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 01) Subsystem: Creative Labs Gameport Joystick Flags: bus master, medium devsel, latency 32 I/O ports at d400 [size=8] Capabilities: [dc] Power Management version 1 0000:00:0b.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang] Flags: bus master, medium devsel, latency 32, IRQ 10 I/O ports at d800 [size=64] 0000:00:0f.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) Subsystem: Avermedia Technologies Inc: Unknown device 0771 Flags: bus master, medium devsel, latency 32, IRQ 5 Memory at eb000000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 0000:00:0f.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) Subsystem: Avermedia Technologies Inc: Unknown device 0771 Flags: bus master, medium devsel, latency 32, IRQ 5 Memory at eb001000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE Flags: bus master, medium devsel, latency 32 I/O ports at dc00 [size=16] Capabilities: [c0] Power Management version 2 0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AQ [Radeon 9600] (prog-if 00 [VGA]) Subsystem: C.P. Technology Co. Ltd: Unknown device 2075 Flags: bus master, 66MHz, medium devsel, latency 255, IRQ 11 Memory at c0000000 (32-bit, prefetchable) [size=256M] I/O ports at c000 [size=256] Memory at e9000000 (32-bit, non-prefetchable) [size=64K] Capabilities: [58] AGP version 2.0 Capabilities: [50] Power Management version 2 0000:01:00.1 Display controller: ATI Technologies Inc RV350 AQ [Radeon 9600] (Secondary) Subsystem: C.P. Technology Co. Ltd: Unknown device 2074 Flags: bus master, 66MHz, medium devsel, latency 32 Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at e9010000 (32-bit, non-prefetchable) [size=64K] Capabilities: [50] Power Management version 2 I disabled acpi in Bios and in Lilo but nothing changes ![]() i forgot, i have a Abit KR7A Motherboard |
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |