LinHES Forums
http://forums.linhes.org/

Cannot complete install
http://forums.linhes.org/viewtopic.php?f=14&t=14682		 Page 1 of 1
Author:  karlec [ Sun Mar 25, 2007 10:04 am ]
Post subject:  Cannot complete install
Can someone help, I wanted to complete the install on an lcd monitor first before moving to a tv and following the instructions for manual install I get stuck a this point:
"Once back to the main menu, select 2. Start installation. Verify the information and sit back. Once complete, reboot the system. After the system reboots it will start X and KnoppMyth will open an Xterm and ask for the root password. See configuration.
The problem is that upon reboot I remove the install disk as per instructions on screen, then after the reboot nothing happens, I get a blinking cursor and that is it.
I installed on a SATA drive and did exactly this "If you have an SATA drive, change this to /KNOPPIX/knoppmyth-sata"

System:
Case: Origen ae X11e
250G Seagate SATA
WD 500G SATA
AMD AM2 X2 4800 (65nm)
PNY NVIDIA 7900 GS
Corsair XMS2 1G
Samsung DVD RW
ASUS M2N2 SLI deluxe
PVR500
Author:  tjc [ Sun Mar 25, 2007 10:16 am ]
Post subject: 
See the troubleshooting pages on the wiki. The most likely problem is that your lilo setup needs to be tweeked and the installer rerun.
http://www.knoppmythwiki.org/index.php?page=WillNotBootAfterInstall
http://www.knoppmythwiki.org/index.php?page=BlackScreenAfterInstall

Also search for posted that mention "mount" and "lilo".
Author:  karlec [ Tue Mar 27, 2007 7:32 pm ]
Post subject: 
I have tried everything posted still it is not working. I have two SATA drives maybe I should disconnect the second one. I am getting really annoyed with it all. Can someone point me to a foolproof way to fix this?!?
Author:  karlec [ Wed Mar 28, 2007 9:09 pm ]
Post subject: 
I tried again and after fixing Lilo it finally rebooted. Now when Lilo comes up I press enter and it starts. first thing :
"Missing or invalid storage location (resume2 = parameter). Please correct or rerun lilo (or equivalent)...
.............
Waiting for /dev to be fully populated usb 1-6 device descriptor read/64 error - 110
usb 1-6 device descriptor read/64 error - 110
usb 1-6 device descriptor read/64 error - 110
.........
Then it continues and then black screen with non-blinking cursor and freezes. The last thing that I see before it freezes (it goes really fast) "starting backend" then I think "installing the nvidia drivers"

after 8 reboots it finally shows the hostname that I selected and ask for login.

What do I do now?

formatted my sda3 drive as xfs so when I changed the info in fstab this is what I added:
/dev/sda3 /mnt/sda3 xfs noauto,users,exec 0 0
#/dev/sda3 /myth xfs auto,users,exec 0 0
Author:  karlec [ Thu Mar 29, 2007 10:02 pm ]
Post subject: 
Exactly what is on the screen after I start today:

Waiting for /dev to be fully populated usb 1-6 device descriptor read/64 error - 110
usb 1-6 device descriptor read/64 error - 110
usb 1-6 device descriptor read/64 error - 110
usb 1-6 device descriptor read/64 error - 110
usb 1-6 device not accepting address 5, error - 110
usb 1-6 device not accepting address 6, error - 110
done.
Activating swap...done.
------Checking root file system ...fsck 1.40-WIP (14-Nov-2006)
/dev/sda1: clean, 07992/3063800 files, 490500/6116740 blocks
done
Checking Multimedia video controller {
Knoppmyth found:
1) Internet Compression Inc ITVC16 (CX23416) MPEG-2 Encoder (rev 01)
2) Internet Compression Inc ITVC16 (CX23416) MPEG-2 Encoder (rev 01)
} Done
Checking file systems ...fsck 1.40-WIP (14-Nov-2006)
done
Setting kernel variables... done
Loading the saved-state of the serial devices...
/dev/tty80 at0x03f8 (irq =4) is a 16550A
Mounting local filesytems ...done
Activating swapfile swap... done
Setting up networking ...
Configuring network interfaces... done
Starting portmap daemon...
Setting cpnsole screen modes and fonts.
Setting the system clock again..
INIT : Entering runlevel: 5
Startiing sytem log daemon...
Starting kernel log daemon...
Starting web server (apache2)...apache2: Could not really determine the server's fully qualified domain name using 127.0.0.1 for ServerName
.
Setting console frame buffer images...using theme 'current'...done
Starting MySql database server: mysqld.
Checking for corrupt, not cleanly closed and upgrade needing tables..
* Not starting internet superserver: no services enabled.
Starting OpenBSD Secure shell server: sshd
Starting system message bus: dbus
Starting hardware abstraction layer: hald
Starting MythTV server: mythbackend.
Starting periodic command scheduler: crond
Checking nVidia video driver installation

Debian GNU/Linux 4.0 karlec tty1

karlec login:





I would really appreciate some help!!

Thanks
Author:  tjc [ Thu Mar 29, 2007 10:18 pm ]
Post subject: 
Sounds like you need to configure your X server. Try logging in as root (using the admin password you entered during the install) and running this command:
Code:
install-nvidia-debian.sh 1.0-8776 -force

BTW - See the "If you are using an Nvidia GeForce 7300 GT with release R5E50" section here: http://www.knoppmythwiki.org/index.php?page=BlackScreenAfterInstall since you've already got a login prompt you don't need to boot from the CD or do any mounting/chrooting.
Author:  karlec [ Fri Mar 30, 2007 12:48 pm ]
Post subject: 
Thanks for your help. I will try that when I get home. My card is a 7900GS can I use the latest version or should I use version 1.0-8776 ?

Thanks
Author:  tjc [ Fri Mar 30, 2007 5:45 pm ]
Post subject: 
I'd try 8776 first, since it'll be much easier. For a newer version the procedure is much more complicated.
Author:  mjl [ Fri Mar 30, 2007 7:27 pm ]
Post subject: 
Hi,

I am a bit curious why the manual install? I am also assuming an R5E50 install since this is the 21 century.. If I recall correctly the auto install R5E50 handled sata quite nicely, even R5C7 handles sata nicely.

Typically some of the bleeding edge hardware may exhibit issues but to get things at least basiclly working you could fall back to using the vesa driver. This would allow you to go through all the setups and in general ensure things are functional.

Once those steps are completed, then it would allow you to concentrate on making the super video card play nice.

The doing a manual install document was originally intended to assist folks when sata first came into play however since that era, Cecil and the great team working quietly behind the scenes with him added sata support which work quite well.

Unless you are planning to marry the two drives into an LVM, start off with the small drive, do an auto install and make it work first. I have a 300gig drive in my KM machine that seems to always have about a hundred gig free and even that is more then I have time view :)

Anytime I have an issue with video at install time, I switch to vesa get the system all setup and then go back and "fine tune" that area.

Just my 2 pennies worth.
Mike
Author:  karlec [ Sun Apr 01, 2007 10:31 am ]
Post subject: 
Thanks Mike. I followed tjc's advice and used the "GefOrce 7300..." instructions and it worked.
Thanks tjc
Now on to getting my PVR500 to work. "No probe info..."

rrrgh!!!
Author:  tjc [ Sun Apr 01, 2007 5:01 pm ]
Post subject: 
Try this: http://www.knoppmythwiki.org/index.php?page=CompileIvtv-0.10.0
Author:  karlec [ Mon Apr 02, 2007 5:23 pm ]
Post subject: 
I can't find "kernel-source-2.6.18-chw-3.tar.bz2" in the /usr/src/ directory.



I recompiled IVTV; now how do I get back to the settings and make sure that my tuner is set up properly
Author:  karlec [ Tue Apr 17, 2007 8:14 am ]
Post subject: 
It turned out that my tuner card was not properly sitting on the PCI "board". However, I still can't get any images from it. I have followed the instructions for blackscreen after install to no avail. I don't know what it is that I'm doing wrong at this point. below are the last few lines of my xsessions-errors log if someone thinks that they can help:

Code:
2007-04-16 19:26:57.104 Connecting to backend server: 127.0.0.1:6543 (try 1 of 5)
2007-04-16 19:26:57.104 Using protocol version 31
2007-04-16 19:26:57.117 TV: Attempting to change from None to WatchingLiveTV
2007-04-16 19:26:57.118 Using protocol version 31
2007-04-16 19:26:58.761 DPMS Deactivated
[mpeg @ 0xb736e7f0]Parser not found for Codec Id: 94210 !
2007-04-16 19:26:58.926 AFD: Opened codec 0x83effc0, id(MPEG2VIDEO) type(Video)
2007-04-16 19:26:58.947 AFD: Opened codec 0x83f0660, id(MP2) type(Audio)
2007-04-16 19:26:58.995 Opening OSS audio device '/dev/dsp'.
2007-04-16 19:26:59.040 VideoOutputXv: XvMCTex: Init failed
2007-04-16 19:26:59.041 VideoOutputXv: XVideo Adaptor Name: 'NV17 Video Texture'
X Error: BadMatch (invalid parameter attributes) 8
  Major opcode:  142
  Minor opcode:  14
  Resource id:  0x1bf
007-04-16 19:26:59.488 TV: Changing from None to WatchingLiveTV
2007-04-16 19:26:59.489 New DB connection, total: 3
2007-04-16 19:26:59.494 Using realtime priority.
2007-04-16 19:26:59.497 Connected to database 'mythconverg' at host: localhost
2007-04-16 19:26:59.603 Video timing method: USleep with busy wait
2007-04-16 19:27:05.268 TV: Attempting to change from WatchingLiveTV to None
2007-04-16 19:27:05.751 TV: Changing from WatchingLiveTV to None
2007-04-16 19:27:05.758 DPMS Reactivated.
2007-04-16 19:34:24.855 Media status changed...  New status is: MEDIASTAT_NOTMOUNTED old status was MEDIASTAT_MOUNTED
2007-04-16 19:34:29.142 Media status changed...  New status is: MEDIASTAT_OPEN old status was MEDIASTAT_NOTMOUNTED
2007-04-16 19:46:10.236 XMLParse::LoadTheme using /usr/share/mythtv/themes/default/dvd-ui.xml
2007-04-16 19:47:52.541 XMLParse::LoadTheme using /usr/share/mythtv/themes/Titivillus/video-ui.xml
2007-04-16 20:19:52.988 Received a remote 'Clear Cache' request


and my dmesg:



ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.10.1 (tagged release) loading
ivtv: Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
tuner 2-0060: chip found @ 0xc0 (ivtv i2c driver #0)
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ivtv0: Autodetected WinTV PVR 500 (unit #1)
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Registered device video0 for encoder MPEG (4 MB)
ivtv0: Registered device video32 for encoder YUV (2 MB)
ivtv0: Registered device vbi0 for encoder VBI (1 MB)
ivtv0: Registered device video24 for encoder PCM audio (1 MB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected Hauppauge card (cx23416 based)
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
ivtv1: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Encoder revision: 0x02060039
tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1)
cx25840 3-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: Autodetected WinTV PVR 500 (unit #2)
ivtv1: Registered device video1 for encoder MPEG (4 MB)
ivtv1: Registered device video33 for encoder YUV (2 MB)
ivtv1: Registered device vbi1 for encoder VBI (1 MB)
ivtv1: Registered device video25 for encoder PCM audio (1 MB)
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv: ==================== END INIT IVTV ====================

Thanks
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/