LinHES Forums :: View topic - Hauppauge remote doesn't work on fresh R5F1 install

T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-chw-13 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:02.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10
B: Alloc= 14/900 us ( 2%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.18-chw-13 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:02.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=01 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0bc7 ProdID=0008 Rev= 1.00
S: Manufacturer=X10 WTI
S: Product=RF receiver
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=lirc_atiusb
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
E: Ad=02(O) Atr=03(Int.) MxPS= 8 Ivl=10ms
/usr/local/bin/lirc-reconfig.sh:
/usr/local/bin/lirc-reconfig.sh: The SnapStream_Firefly remote should be in the$
/usr/local/bin/lirc-reconfig.sh:

Author:	adentone [ Fri May 18, 2007 4:10 pm ]
Post subject:	Hauppauge remote doesn't work on fresh R5F1 install
This was a Tier 1 install all the way, except that my grey Hauppauge remote doesn't work. On my previous Knoppmyth installation, it guided me through a wizard that helped me install the remote. R5F1 install didn't ask me for it. The IR receiver is plugged into the PVR350, as is TV-out (which works great). My wife doesn't want to use the keyboard, so can someone help point me in the right direction? Many thanks!

Author:	slowtolearn [ Fri May 18, 2007 4:14 pm ]
Post subject:
Does this help? http://mysettopbox.tv/phpBB2/viewtopic.php?t=15219

Author:	adentone [ Sun May 20, 2007 11:19 am ]
Post subject:	nope, not yet...
I have tried these things from the above post: 1) Cold Reboot (10min, 50min) // I was really hoping this one would work! 2) commented out the modprobe for saa7134-dvb as such: Code: modprobe dvb-bt8xx modprobe nvram /usr/local/bin/tvterm.sh #modprobe saa7134-dvb modprobe cx88-dvb echo "} Done" ######################################################################## # End 3) lirc-reconfig.sh none of the 3 Hauppauge options work 4) Quote: which says that DEVICE should equal "/dev/lirc0" and not "/dev/lirc/0". In /etc/init.d/lirc , line 34, it indeed refers to /dev/lirc/0, so I changed it to /dev/lirc0. * Also, in line 83 of /etc/init.d/lirc, there is a line that ends "$LIRCD_ARGS\" That backslash didn't look right so I put a space there: "$LIRCD_ARGS \" I have rebooted countless times between each config change (still a Windows user - bad habit, I know) My remote has fresh batteries, it is the Grey/Silver Hauppauge with the colored buttons at the bottom. It looks like everything else is working..... thanks for your help on this!

Author:	ceenvee703 [ Sun May 20, 2007 12:07 pm ]
Post subject:
The only things that I did that I didn't see you did are: * confirm that you've got an /etc/lircd.conf as a symlink to /etc/lirc/lircd.conf * edit your lircd.conf file... after selecting the gray remote from the lirc-reconfig script, there are three independent listings for Hauppauge remotes in this one file. I am pretty sure I deleted the first and third ones and left the second (the first one seemed generic, the third one seemed to be for the "dogbone" remote). You might try renaming and moving that ir_kbd_i2c module: I did that in addition to commenting out the saa module just in case that wasn't sufficient.

Author:	adentone [ Sun May 20, 2007 9:28 pm ]
Post subject:
ceenvee703 wrote: The only things that I did that I didn't see you did are: * confirm that you've got an /etc/lircd.conf as a symlink to /etc/lirc/lircd.conf * edit your lircd.conf file... after selecting the gray remote from the lirc-reconfig script, there are three independent listings for Hauppauge remotes in this one file. I am pretty sure I deleted the first and third ones and left the second (the first one seemed generic, the third one seemed to be for the "dogbone" remote). You might try renaming and moving that ir_kbd_i2c module: I did that in addition to commenting out the saa module just in case that wasn't sufficient. Ok - so now I have: 1) re-created the symlink to /etc/lirc/lircd.conf 2) only one remote is listed in my /etc/lirc/lircd.conf file i'll see if I can find the instruction to rename / move the ir_kbd_i2c module... any other ideas? what are some good remotes people like/ ( I have four and would like to use one... ) Thanks!

LinHES Forums http://forums.linhes.org/

Hauppauge remote doesn't work on fresh R5F1 install http://forums.linhes.org/viewtopic.php?f=14&t=15275	Page 1 of 1

Author:	adentone [ Mon May 21, 2007 10:56 am ]
Post subject:	ok... so....
I did this: Code: lsmod \| awk '$3 == 0 { print $1 }' \| sort and ir_kbd_i2c isn't in the list. The list: Code: 8250_pnp ac agpgart autofs4 battery button container cx8800 cx8802 cx88_vp3054_i2c dvb_bt8xx dvb_pll ehci_hcd eth1394 fan fuse i2c_nforce2 lirc_i2c msp3400 nvram ohci1394 ohci_hcd parport_pc pcmcia saa7115 saa7127 sbp2 sbs serio_raw snd_intel8x0 snd_pcm_oss thermal tsdev tuner uhci_hcd unionfs usb_storage usbhid video video_buf_dvb yenta_socket I have three tuner cards, the IR Receiver is attached to the last PVR-250 (pci slot 3). I am tempted to go buy a SnapStream Firefly... any other suggestions?

Author:	adentone [ Wed Jun 06, 2007 12:40 pm ]
Post subject:	same problem
I bought a SnapStream Firefly, connected it and rebooted, re-configured lirc, rebooted, rebooted, rebooted, and still no love from the remote... I am pretty frustrated at this point, but very willing to try anything! Please, your helpful hints will be greatly appreciated!

Author:	ceenvee703 [ Wed Jun 06, 2007 3:57 pm ]
Post subject:
I bought a Firefly for a remote front end, and it was automatically recognized WHEN I ran lirc-reconfig.sh -- when you say you "reconfigured lirc" do you mean you ran lirc-reconfig.sh ? If you ran it, did it say it recognized the Snapstream remote?

Author:	adentone [ Wed Jun 06, 2007 10:51 pm ]
Post subject:
NO, it said that it SHOULD HAVE BEEN ABLE to detect it automatically, but didn't, and to email the contents of a log file to a @gmail.com address. I would do that, but I didn't because I don't know how to get that all working from the command line. (ok, ok, I'm a n00b...) thanks for any help...

Author:	forkd [ Wed Jun 06, 2007 11:06 pm ]
Post subject:	I'm guessing
After you run lirc-reconfig.sh have you tried doing irw. I've been having a lot of issues with my remote, ir receiver attached to the pvr-250 using the silver hauppauge remote, and I check by running IRW. at command line type IRW now when you press the remote do you see anything. **I know this is probably the most basic thing but it is my first step usually

Author:	adentone [ Wed Jun 06, 2007 11:14 pm ]
Post subject:
I have not, let me try that... nope, IRW seems to wait for input, then I tried the remote and nothing appears. I did Ctrl-Z to stop. Does it matter that I did this over PuTTY? thanks - what next?

Author:	adentone [ Wed Jun 06, 2007 11:54 pm ]
Post subject:	/var/log/mythtv/lirc-reconfig.log contents
Code: T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.18-chw-13 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:02.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 B: Alloc= 14/900 us ( 2%), #Int= 1, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.18-chw-13 ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0bc7 ProdID=0008 Rev= 1.00 S: Manufacturer=X10 WTI S: Product=RF receiver C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=lirc_atiusb E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms E: Ad=02(O) Atr=03(Int.) MxPS= 8 Ivl=10ms /usr/local/bin/lirc-reconfig.sh: /usr/local/bin/lirc-reconfig.sh: The SnapStream_Firefly remote should be in the$ /usr/local/bin/lirc-reconfig.sh:

Page 1 of 1	All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/