Just tried installing R5V10, and the CD does a great job at copying files to my hard drive. It boots up fine, but when I add a capture card and choose DVB, it says, "Could not open card #0!, Device or resource busy".
I tried modprobe dvb-bt8xx and modprobe dst, then re-running myth-setup .. still the same ..
I tried adding dvb-bt8xx and dst to the end of /etc/modules .. still the same ..
Anybody gotten visionplus card to work on R5V10 yet?
Here's part of my dmesg output:
Code:
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 5 (level, low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:01:09.0, irq: 5, latency: 32, mmio: 0xd4000000
bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0001
bttv0: using: Twinhan DST + clones [card=113,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00f100fe [init]
bttv0: using tuner=4
tuner: Ignoring new-style parameters in presence of obsolete ones
bttv0: add subdevice "dvb0"
bttv: Bt8xx card found (1).
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 7 (level, low) -> IRQ 7
bttv1: Bt878 (rev 17) at 0000:01:0a.0, irq: 7, latency: 32, mmio: 0xd4002000
bttv1: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0001
bttv1: using: Twinhan DST + clones [card=113,autodetected]
bttv1: gpio: en=00000000, out=00000000 in=00f100fe [init]
bttv1: using tuner=4
bttv1: add subdevice "dvb1"
...
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI interrupt 0000:01:09.1[A] -> GSI 5 (level, low) -> IRQ 5
bt878(0): Bt878 (rev 17) at 01:09.1, irq: 5, latency: 32, memory: 0xd4001000
bt878: Bt878 AUDIO function found (1).
ACPI: PCI interrupt 0000:01:0a.1[A] -> GSI 7 (level, low) -> IRQ 7
bt878(1): Bt878 (rev 17) at 01:0a.1, irq: 7, latency: 32, memory: 0xd4003000
attach: checking "bt878 #0 [hw]"
find by pci: checking "bt878 #0 [hw]"
attach: "bt878 #0 [hw]", to card 0
attach: checking "bt878 #1 [hw]"
find by pci: checking "bt878 #1 [hw]"
attach: "bt878 #1 [hw]", to card 1
DVB: registering new adapter (DST).
DVB: registering new adapter (DST).
bt878 find by dvb adap: checking "DST"
dst_check_ci: recognize DTTDIG
DST type : terrestial TV
DST type flags :
DVB: registering frontend 0:0 (DST TERR)...
bt878 find by dvb adap: checking "DST"
dst_check_ci: recognize DTTDIG
DST type : terrestial TV
DST type flags :
DVB: registering frontend 1:0 (DST TERR)...