| LinHES Forums http://forums.linhes.org/ |
|
| R5V10 Visionplus DVB-T (Could not open card) http://forums.linhes.org/viewtopic.php?f=14&t=3701 |
Page 1 of 1 |
| Author: | sammo2828 [ Sat Feb 26, 2005 12:37 am ] |
| Post subject: | R5V10 Visionplus DVB-T (Could not open card) |
Just tried installing R5V10, and the CD does a great job at copying files to my hard drive. It boots up fine, but when I add a capture card and choose DVB, it says, "Could not open card #0!, Device or resource busy". I tried modprobe dvb-bt8xx and modprobe dst, then re-running myth-setup .. still the same .. I tried adding dvb-bt8xx and dst to the end of /etc/modules .. still the same .. Anybody gotten visionplus card to work on R5V10 yet? Here's part of my dmesg output: Code: Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 5 (level, low) -> IRQ 5 bttv0: Bt878 (rev 17) at 0000:01:09.0, irq: 5, latency: 32, mmio: 0xd4000000 bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00f100fe [init] bttv0: using tuner=4 tuner: Ignoring new-style parameters in presence of obsolete ones bttv0: add subdevice "dvb0" bttv: Bt8xx card found (1). ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 7 (level, low) -> IRQ 7 bttv1: Bt878 (rev 17) at 0000:01:0a.0, irq: 7, latency: 32, mmio: 0xd4002000 bttv1: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0001 bttv1: using: Twinhan DST + clones [card=113,autodetected] bttv1: gpio: en=00000000, out=00000000 in=00f100fe [init] bttv1: using tuner=4 bttv1: add subdevice "dvb1" ... bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI interrupt 0000:01:09.1[A] -> GSI 5 (level, low) -> IRQ 5 bt878(0): Bt878 (rev 17) at 01:09.1, irq: 5, latency: 32, memory: 0xd4001000 bt878: Bt878 AUDIO function found (1). ACPI: PCI interrupt 0000:01:0a.1[A] -> GSI 7 (level, low) -> IRQ 7 bt878(1): Bt878 (rev 17) at 01:0a.1, irq: 7, latency: 32, memory: 0xd4003000 attach: checking "bt878 #0 [hw]" find by pci: checking "bt878 #0 [hw]" attach: "bt878 #0 [hw]", to card 0 attach: checking "bt878 #1 [hw]" find by pci: checking "bt878 #1 [hw]" attach: "bt878 #1 [hw]", to card 1 DVB: registering new adapter (DST). DVB: registering new adapter (DST). bt878 find by dvb adap: checking "DST" dst_check_ci: recognize DTTDIG DST type : terrestial TV DST type flags : DVB: registering frontend 0:0 (DST TERR)... bt878 find by dvb adap: checking "DST" dst_check_ci: recognize DTTDIG DST type : terrestial TV DST type flags : DVB: registering frontend 1:0 (DST TERR)... |
|
| Author: | sammo2828 [ Sat Feb 26, 2005 12:51 am ] |
| Post subject: | |
Hmm .. turns out myth-backend was running during post-install .. anyways, i did a /etc/init.d/myth-backend stop and the problem is solved .. now onto tuning and epg .. seeya! |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|