| LinHES Forums http://forums.linhes.org/ |
|
| Nvidia logo... i see it on the screen but what next?! http://forums.linhes.org/viewtopic.php?f=14&t=4090 |
Page 1 of 1 |
| Author: | Ecct123 [ Wed Apr 06, 2005 5:46 pm ] |
| Post subject: | Nvidia logo... i see it on the screen but what next?! |
Hey i just did an auto install, everything was going good... my setup: 1.7 ghz P4 PVR350 512 ddr 200 gig ide hd g-force 4 mx 4000 agp I installed the nvidia drivers, then installed XvMC and LIRC support on Pentium Pro/Athlon machines. Then i edited the XF86Config-4 and put Option "ConnectedMonitor" "TV" Now I get an nvidia logo over the whole screen, it comes up fine on the tv but if i put the computer back on a monitor it's blank. Is there a command to start myth going? cause when i reboot all i see is the nvidia logo now. --- EDIT: I fixed the freezing nvidia logo by updating to the newest nvidia drivers. Now myth runs like it should, but i get no TV in from my pvr 350... it just says "Can't initialize video" I did the auto install from the newest iso released. Do I need to install a new version of ivtv also? thanks for any help... |
|
| Author: | gr8nash [ Sat Apr 09, 2005 9:08 am ] |
| Post subject: | |
Code: Option "ConnectedMonitor" "TV" is an onptional command to FORCE nvidia to use TV out.. that is why you would only get video on your Svideo not your vga plug.. i dont use it. the only options i use are: Code: Option "TVStandard" "NTSC-M"
Option "TVOutFormat" "SVIDEO" this doesnt force output so it should detect svidio and use it for the tv.. and if you reboot and plugin vga it should detect that and work.. you should only use Option "ConnectedMonitor" "TV" if its not detecting your TV and you want to FORCE it.. |
|
| Author: | tjc [ Sat Apr 09, 2005 9:40 am ] |
| Post subject: | |
Actually there are other reasons for using Option "ConnectedMonitor" "TV". My system wouldn't display X on the TV without a explicit ConnectedMonitor spec, even if I told it to use TwinView. Also, once you get past initial setup you'll generally want to set it for TV only so that Xv will work properly. |
|
| Author: | gr8nash [ Sat Apr 09, 2005 9:48 am ] |
| Post subject: | |
Quote: you'll generally want to set it for TV only so that Xv will work properly.
XV seems to work great for me for six months now.. i think your hadcoding it goes back to what i said about system not decting the tv properly. because none of my systems i need to hardcode tv.. and several are HD systems so i would *think* i would see XV not working on those systems.. |
|
| Author: | tjc [ Sat Apr 09, 2005 10:05 am ] |
| Post subject: | |
Maybe this isn't an issue with the newer Nvidia drivers, but when I was first setting up my system, getting TV Out working required substantial application of brute force. If you weren't explicit about the TV, X wouldn't work on it. I also started off in TwinView with the monitor plugged in so that I had a working display available while struggling with this and swapped back and forth between "known working" and experimental versions of XF86Config-4. In that case you had to be explicit that the TV was the only display you want it talking to. Also while using TwinView the ConnectedMonitor option lets you specify the order of the two displays... |
|
| Author: | Xsecrets [ Sat Apr 09, 2005 11:06 am ] |
| Post subject: | |
I must say that the connectedmonitor like got into the documentation initially because I insisted, because it would not work on my nforce2 onboard tvout without it. I think the type of video card makes a big difference as well, because at the time cesman was not needing to use it either. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|