LinHES Forums :: View topic - Actisys200L and R5A15 using iwamble.net instructions

LinHES Forums http://forums.linhes.org/

Actisys200L and R5A15 using iwamble.net instructions http://forums.linhes.org/viewtopic.php?f=14&t=4291	Page 1 of 1

Author:	elgordo123 [ Tue Apr 26, 2005 4:54 pm ]
Post subject:	Actisys200L and R5A15 using iwamble.net instructions
I had this working on R4V5 (or last stable).. I get errors using R5A15. I followed the instructions on www.iwamble.net. I had to remove the --tag=CC flags to get it to compile and then installed it. I used lirc-0.7.1pre4.tar.bz2. (modified the lirc2remote so it would work of course, which it did). Whenever I try to change_channel.csh I get errors: remote_irsend: command failed: SEND_ONCE JVC_RAW 2 remote_irsend: transmission failed remote_irsend: command failed: SEND_ONCE JVC_RAW 4 remote_irsend: transmission failed remote_irsend: command failed: SEND_ONCE JVC_RAW 8 remote_irsend: transmission failed /usr/local/bin/remote_irsend: command failed: SEND_ONCE JVC_RAW SELECT /usr/local/bin/remote_irsend: transmission failed I am using JVC_RAW as my /etc/remoted.conf (and in channel.pl). Here is my dmesg from boot: kernel: remote_dev: IR Remote Control driver registered, at major 72 mythtv kernel: remote_dev: remote_register_plugin: sample_rate: 0 mythtv kernel: remote_sir: I/O port 0x02f8, IRQ 3. mythtv kernel: remote_sir: Installed. mythtv kernel: lirc_dev: IR Remote Control driver registered, at major 61 mythtv kernel: bttv: driver version 0.9.15 loaded mythtv kernel: bttv: using 8 buffers with 2080k (520 pages) each for capture mythtv kernel: cx2388x v4l2 driver version 0.0.4 loaded mythtv kernel: lirc_i2c: chip found @ 0x18 (Hauppauge IR) mythtv kernel: ivtv: i2c attach [client=Hauppauge IR,ok] mythtv kernel: lirc_dev: lirc_register_plugin:sample_rate: 10 mythtv kernel: lirc_i2c: chip found @ 0x18 (Hauppauge IR) mythtv kernel: ivtv: i2c attach [client=Hauppauge IR,ok] mythtv kernel: lirc_dev: lirc_register_plugin:sample_rate: 10 Here is my /var/log/remoted: mythtv remoted 0.7.1pre4: error processing command: SEND_ONCE JVC_RAW 2 mythtv remoted 0.7.1pre4: transmission failed mythtv remoted 0.7.1pre4: removed client mythtv remoted 0.7.1pre4: accepted new client on /dev/remoted mythtv remoted 0.7.1pre4: too short gap: 100000 mythtv remoted 0.7.1pre4: error processing command: SEND_ONCE JVC_RAW 4 mythtv remoted 0.7.1pre4: transmission failed mythtv remoted 0.7.1pre4: removed client mythtv remoted 0.7.1pre4: accepted new client on /dev/remoted mythtv remoted 0.7.1pre4: too short gap: 100000 mythtv remoted 0.7.1pre4: error processing command: SEND_ONCE JVC_RAW 8 mythtv remoted 0.7.1pre4: transmission failed mythtv remoted 0.7.1pre4: removed client mythtv remoted 0.7.1pre4: accepted new client on /dev/remoted mythtv remoted 0.7.1pre4: too short gap: 100000 mythtv remoted 0.7.1pre4: error processing command: SEND_ONCE JVC_RAW SELECT mythtv remoted 0.7.1pre4: transmission failed Here is my bootmisc.sh file: /usr/local/sbin/lircd (added when I first started/installed lircd) # Starting Actisys stuff echo "Starting remoted..." setserial /dev/ttyS1 uart none /sbin/modprobe remote_sir /usr/local/sbin/remoted List of my /dev directory settings, chmod 777 on all /dev/remote* crwxrwxrwx 1 root root 72, 0 Apr 26 14:48 /dev/remote srwxrwxrwx 1 root root 0 Apr 26 15:25 /dev/remoted prwxrwxrwx 1 root root 0 Apr 26 15:02 /dev/remotem Once again thanks in advance...

Author:	elgordo123 [ Tue Apr 26, 2005 6:17 pm ]
Post subject:
It may be related, but my regular lirc for my hauppage remote doesn't work either. I dont see any errors on any logs about this. Maybe they are related?

Author:	elgordo123 [ Thu Apr 28, 2005 12:17 am ]
Post subject:	Progress Made but still problems
Here is my status so far.... After I rebooted I got the JVC_RAW (can't find remoted.conf) problem resolved. I learned after I changed it, I had to kill remoted and then restart it. If I run one of the remotes config files I dont get any errors at all, but nothing happens on the box. Before I was using the JVC_RAW (raw codes, which looks VERY different than anything I see in the remotes pre-made confi files). (I have attached it). The error I am getting with that is this: transmission failed removed client accepted new client on /dev/remoted too short gap: 100000 I have tried the JVC_4700, and the Dishnetwork 301 one, but again they look completely different than the RAW codes one that was working. I tried to change the gap to like 20000 or 6200 (seen from other config files) but they still dont do anything. One thing that I did in my original setup was to change my dishnetwork receiver to address 9. Here is an excerpt from the remoted.conf file that WAS working before the upgrade. You can see it is very different than what is in the standard lirc remotes config files. begin remote name JVC_RAW flags CONST_LENGTH\|RAW_CODES eps 30 aeps 100 ptrail 0 repeat 0 0 gap 100000 begin raw_codes name tv/video 500 6035 500 2805 500 1685 500 2805 500 1685 500 1685 500 1685 500 2805 500 2805 500 2805 500 1685 500 2805 500 2805 500 2805 500 2805 500 2805 500 2805 500 6035 500 2805 500 1685 500 2805 500 1685 500 1685 500 1685

Author:	elgordo123 [ Thu Apr 28, 2005 12:04 pm ]
Post subject:
It is now working. Really they only thing I needed to do was to increase the gap size in the remoted.conf file. Increased it from 100000 to 175000 and everything works now.

Page 1 of 1	All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/