| LinHES Forums http://forums.linhes.org/ |
|
| DVICO Fusion Dual Digitial - only one tuner working http://forums.linhes.org/viewtopic.php?f=15&t=10779 |
Page 1 of 1 |
| Author: | dvbn0ob_r [ Mon Jul 10, 2006 5:54 pm ] |
| Post subject: | DVICO Fusion Dual Digitial - only one tuner working |
I've installed knoppmythtv latest version, downloaded and recompiled v4l-dvb and added the appropriate firmware updates to /usr/lib/hotplug/firmware. So now the card is auto detected correctly type 44. But I get some errors in dmesg about the device being plugged into a 1.1 port (a7n8x has 1.1 and 2.0 controllers). lsusb -v reports the device as usb2.0 The end result is that doing a tzap with adapter 0 doesn't work correctly, The first line has a little signal and subsequent lines have 0 signal. tzap with adapter 1 get's lock. So any ideas, is kernel options, should i look at hardware and what interrupts are shared and where things are plugged in? A7N8X-E(Deluxe) FX5200 |
|
| Author: | dvbn0ob_r [ Fri Jul 14, 2006 9:53 pm ] |
| Post subject: | |
So tried the moving some things around hardware, pulled some stuff out to reduce power consumption etc. And now the other error about being plugged into 1.1 is gone. But i still have the same problem, adapter 0 doesn't get much of a signal when i tzap on it. Device 1 is good sh-3.00$ tzap -a 1 "ABC TV Brisbane" using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0' reading channels from file '/home/mythtv/.tzap/channels.conf' tuning to 226500000 Hz video pid 0x0200, audio pid 0x028a status 01 | signal 2e5f | snr 0000 | ber 00000000 | unc 00000000 | status 1f | signal 251f | snr cdcd | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1f | signal 267f | snr d2d2 | ber 00000000 | unc 00000000 | FE_HAS_LOCK Device 0 is bad sh-3.00$ tzap "ABC TV Brisbane" using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' reading channels from file '/home/mythtv/.tzap/channels.conf' tuning to 226500000 Hz video pid 0x0200, audio pid 0x028a status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | status 00 | signal 000f | snr 0000 | ber 00000000 | unc 00000000 | signal was 000f constantly, but on other runs it starts at 128f. there is a usb error but later on when ehci is init it indicates that a device is found ok. here is the complete dmesg dump, notice the timeout's at the end, do I need to increase latency on something? Linux version 2.6.15-chw-2 (root@dev.mysettopbox.tv) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 SMP PREEMPT Thu Jan 5 08:10:40 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 126960 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:0 DMI 2.2 present. ACPI: RSDP (v000 Nvidia ) @ 0x000f6d60 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff74c0 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=301 splash=silent apm=power-o ff nomce bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1243.420 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 512964k/524224k available (3151k kernel code, 10732k reserved, 1029k dat a, 220k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2488.89 BogoMIPS (lpj=1244448) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 0 0000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 0000000 0 00000000 mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: AMD Athlon(tm) stepping 00 Total of 1 processors activated (2488.89 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 1 CPUs checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 56k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb4b0, last bus=2 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: nForce2 C1 Halt Disconnect fixup Boot video device is 0000:02:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled. ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled. ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled. ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:00: ioport range 0x4000-0x407f could not be reserved pnp: 00:00: ioport range 0x4080-0x40ff has been reserved pnp: 00:00: ioport range 0x4400-0x447f has been reserved pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved pnp: 00:00: ioport range 0x4200-0x427f has been reserved pnp: 00:00: ioport range 0x4280-0x42ff has been reserved pnp: 00:01: ioport range 0x5000-0x503f has been reserved pnp: 00:01: ioport range 0x5500-0x553f has been reserved PCI: Bridge: 0000:00:08.0 IO window: 9000-afff MEM window: de000000-e1ffffff PREFETCH window: 30000000-300fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: dc000000-ddffffff PREFETCH window: d0000000-d7ffffff PCI: Setting latency timer of device 0000:00:08.0 to 64 Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFS: nTxBlock = 4009, nTxLock = 32072 SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered isapnp: ScanniPNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE2: IDE controller at PCI slot 0000:00:09.0 NFORCE2: chipset revision 162 NFORCE2: not 100% native mode: will probe irqs later NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: IC35L040AVER07-0, ATA DISK drive hdb: ATAPI DVD-ROM 16X Maximum, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: CW038D ATAPI CD-R/RW, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB ng for PnP cards... isapnp: No Plug & Play device found hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=65535/16/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 hda3 hdb: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) libata version 1.20 loaded. sata_sil 0000:01:0b.0: version 0.9 ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IR Q 16 ata1: SATA max UDMA/100 cmd 0xE0802080 ctl 0xE080208A bmdma 0xE0802000 irq 16 ata2: SATA max UDMA/100 cmd 0xE08020C0 ctl 0xE08020CA bmdma 0xE0802008 irq 16 ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48 ata1: dev 0 configured for UDMA/100 scsi0 : sata_sil ata2: no device found (phy stat 00000000) scsi1 : sata_sil Vendor: ATA Model: ST3160827AS Rev: 3.03 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back sda: sda1 sd 0:0:0:0: Attached scsi disk sda mice: PS/2 mouse device common for all mice md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid10 personality registered as nr 9 md: raid5 personality registered as nr 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 3304.000 MB/sec raid5: using function: pIII_sse (3304.000 MB/sec) raid6: int32x1 472 MB/s raid6: int32x2 593 MB/s raid6: int32x4 355 MB/s raid6: int32x8 355 MB/s raid6: mmxx1 1035 MB/s raid6: mmxx2 1714 MB/s raid6: sse1x1 992 MB/s raid6: sse1x2 1628 MB/s raid6: using algorithm sse1x2 (1628 MB/s) md: raid6 personality registered as nr 8 md: multipath personality registered as nr 7 md: faulty personality registered as nr 10 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP route cache hash table entries: 8192 (order: 3, 32768 bytes) TCP established hash table entries: 32768 (order: 6, 393216 bytes) TCP bind hash table entries: 32768 (order: 6, 393216 bytes) TCP: Hash tables configured (established 32768 bind 32768) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 15 Using IPI No-Shortcut mode Suspend2 Core. Suspend2 Compression Driver loading. Suspend2 Encryption Driver loading. Suspend2 Swap Writer loading. Suspend2 FileWriter loading. ACPI wakeup devices: HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1 ACPI: (supports S0 S1 S4 S5) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). input: AT Translated Set 2 keyboard as /class/input/input0 input: ImPS/2 Generic Wheel Mouse as /class/input/input1 (fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status 0, recover ed transactions 20217 to 20311 (fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 1863 and revoked 3/14 b locks EXT3-fs warning: maximal mount count reached, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Suspend2: Initrd lacks echo > /proc/suspend2/do_resume. Freeing unused kernel memory: 220k freed Adding 769096k swap on /dev/hda2. Priority:-1 extents:1 across:769096k EXT3 FS on hda1, internal journal usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.3 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) -> IR Q 17 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 17, io mem 0xe2080000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level, high) -> IR Q 18 PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: OHCI Host Controller ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.1: irq 18, io mem 0xe2083000 usb 1-2: new full speed USB device using ohci_hcd and address 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org> ACPI: PCI Interrupt Link [APCM] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 20 (level, high) -> IR Q 19 PCI: Setting latency timer of device 0000:00:0d.0 to 64 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e2084000-e20847ff] Max Packet=[2048] Real Time Clock Driver v1.12 ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state, will try to lo ad a firmware parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] Linux video capture interface: v2.00 cx2388x dvb driver version 0.0.6 loaded CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [ card=44,autodetected] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:01:09.2[A] -> Link [APC2] -> GSI 17 (level, high) -> IR Q 20 cx88[0]/2: found at 0000:01:09.2, rev: 5, irq: 20, latency: 32, mmio: 0xdf000000 cx88[0]/2: cx2388x based dvb card DVB: registering new adapter (cx88[0]). DVB: registering frontend 0 (Zarlink MT352 DVB-T)... i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5000 i2c_adapter i2c-2: nForce2 SMBus adapter at 0x5500 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected NVIDIA nForce2 chipset agpgart: AGP aperture is 64M @ 0xd8000000 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IR Q 17 PCI: Setting latency timer of device 0000:00:04.0 to 64 eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0 cx2388x v4l2 driver version 0.0.6 loaded ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IR Q 20 cx88[0]/0: found at 0000:01:09.0, rev: 5, irq: 20, latency: 32, mmio: 0xde000000 cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) -> IR Q 18 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 51574 usecs intel8x0: clocking to 47455 NET: Registered protocol family 17 dvb-usb: did not find the firmware file. (dvb-usb-bluebird-01.fw) Please see lin ux/Documentation/dvb/ for more details on firmware-problems. (-2) dvb_usb_cxusb: probe of 1-2:1.0 failed with error -22 usbcore: registered new driver dvb_usb_cxusb usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bt878: AUDIO driver version 0.0.0 loaded saa7146: register extension 'dvb'. saa7146: register extension 'budget dvb'. saa7146: register extension 'budget_ci dvb'. saa7146: register extension 'budget_av'. usbcore: registered new driver ttusb usbcore: registered new driver ttusb-dec NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver kjournald starting. Commit interval 5 seconds EXT3 FS on hda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! lirc_dev: IR Remote Control driver registered, at major 61 ts: Compaq touchscreen protocol output input: PC Speaker as /class/input/input2 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A eth0: no IPv6 routers present ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 20 (level, high) -> IR Q 19 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: EHCI Host Controller ehci_hcd 0000:00:02.2: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:02.2: irq 19, io mem 0xe2086000 ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected usb 1-2: USB disconnect, address 2 usb 3-2: new high speed USB device using ehci_hcd and address 2 dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state, will try to lo ad a firmware dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw' usb 3-2: USB disconnect, address 2 dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. usb 3-2: new high speed USB device using ehci_hcd and address 3 dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual USB). DVB: registering frontend 1 (Zarlink MT352 DVB-T)... input: IR-receiver inside an USB DVB receiver as /class/input/input3 dvb-usb: schedule remote query interval to 150 msecs. dvb-usb: DViCO FusionHDTV DVB-T Dual USB successfully initialized and connected. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 cx2388x blackbird driver version 0.0.6 loaded nvidia: module license 'NVIDIA' taints kernel. nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IR Q 21 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:44: 39 PST 2005 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout cx88[0]/2: cx8802_timeout |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|