Yes I did
| LinHES Forums http://forums.linhes.org/ |
|
| Has DVB channel scan improved? http://forums.linhes.org/viewtopic.php?f=15&t=11411 |
Page 1 of 1 |
| Author: | tophee [ Fri Sep 01, 2006 4:07 am ] |
| Post subject: | Has DVB channel scan improved? |
Hi, Quick question: I read a while ago people with R5C7 as clean install had problems with picking up and locking onto channels on DVB-T scans. Has this is been resolved in R5D1? Thanks. |
|
| Author: | Quigs [ Fri Sep 01, 2006 5:30 am ] |
| Post subject: | |
It will be in 0.20 - don't think much has changed with the current 0.19 branch R5D1 is on. |
|
| Author: | tophee [ Fri Sep 01, 2006 9:22 am ] |
| Post subject: | |
Arse. I was hoping to do a fresh install, but it can wait. |
|
| Author: | 0ctane [ Fri Sep 01, 2006 2:58 pm ] |
| Post subject: | |
Quigs wrote: It will be in 0.20 - don't think much has changed with the current 0.19 branch R5D1 is on. ugg...
I just wiped a gentoo install to get Knoppmyth, and now you are telling me that channel scanning DVB-T might not be working? That is exactly the problem I am having. My card (FusionHDTV-III) was recognised, but I cannot tune any channels. Is there a fix? |
|
| Author: | tophee [ Fri Sep 01, 2006 5:08 pm ] |
| Post subject: | |
Bad one, I think it's a case of try, try again... I remember seeing people having problems with clean installs of R5C7. I was hoping they were fixed. I think the resolution was just to keep on scanning for channels... eventually it will pick up channels or enter the information manually. (Hopefully this will be of some use..) 'Fraid I cant offer more info. |
|
| Author: | 0ctane [ Fri Sep 01, 2006 6:26 pm ] |
| Post subject: | |
Well, I am getting kernel problems too when sound levels are trying to be set during installation. Guess I will have to come back to Knoppmyth in a few months and cross my fingers. |
|
| Author: | Girkers [ Sun Sep 03, 2006 4:00 pm ] |
| Post subject: | |
In Aussie Land when I installed R5C7 I scanned for channels fine. It just didn't pick up the weaker signalled SBS. To correct this I put as much information into the scanner before starting and then it picked it up fine. |
|
| Author: | tophee [ Mon Sep 04, 2006 6:06 am ] |
| Post subject: | |
Sweet, I may reinstall with R5C7 then. Did you get your information from dvbscan uk-<Your Transmitter> | tee channels.conf first? Ta |
|
| Author: | Girkers [ Thu Sep 07, 2006 4:14 pm ] |
| Post subject: | |
Yes I did
|
|
| Author: | nich010 [ Fri Sep 08, 2006 10:28 am ] |
| Post subject: | DVB with R5C7 and Nova-T in UK |
tophee wrote: Sweet, I may reinstall with R5C7 then.
Did you get your information from dvbscan uk-<Your Transmitter> | tee channels.conf first? Ta R5C7 was my first knoppmyth install, and auto scan picked up most channels (My transmitter is Hannington, west of Basingstoke) Manually adding channels from a channels.conf filled the gaps. More recently however an auto-scan on a clean install of R5C7 did even better, and a couple of scans (dunno why this helps) seems to have picked up all available channels. |
|
| Author: | tophee [ Fri Sep 08, 2006 10:40 am ] |
| Post subject: | |
Thanks guys, Though it would. From an earlyer install of KnoppMyth (R5A26) I used the above command and in 30.1 I used the rescan trick. I wanted to check before I started. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|