Thanks Dale
the Fix
Code:
append="resume2=swap:/dev/hda2 noresume2"
lilo -v
works perfect
| LinHES Forums http://forums.linhes.org/ |
|
| Newbie: Suspend2 2.2.8.4 at startup KnoppMyth http://forums.linhes.org/viewtopic.php?f=17&t=13508 |
Page 1 of 1 |
| Author: | clive_r_long [ Sun Jan 14, 2007 1:37 pm ] |
| Post subject: | Newbie: Suspend2 2.2.8.4 at startup KnoppMyth |
Hi I have "successfully" (that's what the messages said) installed knoppmyth R5E50 under Fedora 5 kernel 2.6.18-1.2257.fc5 > VMWare 6. That hardware and VMWare6 version is successfully running Win XP Pro SP1 and connects various USB2 devices. Now, when I boot the KnoppMyth virtual machine I see the following message scrolling quickly on the console Suspend2 2.2.8.4 Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending. The VM has 256Mbyte memory. Any idea where the or what the problem could be or how to fix it? I am trying to run a Freecom / AVerMEdia USB DVB-T device with KnoppMyth. Anyone had success with that device? Thanks Clive |
|
| Author: | tjc [ Sun Jan 14, 2007 1:49 pm ] |
| Post subject: | |
Know and ignorable. You may also notice some initial warnings from udev and apache. |
|
| Author: | clive_r_long [ Sun Jan 14, 2007 1:59 pm ] |
| Post subject: | |
tjc wrote: Know and ignorable. You may also notice some initial warnings from udev and apache.
Thanks for the very prompt reply. Unfortunately, the suspend2 messages just seem to loop until the following failure messages /linuxrc: Out of file descriptors /etc/init: Out of file descriptors Kernel panic - not syncing: Attempted to kill init! after about 15 seconds-ish Clive |
|
| Author: | JoeF [ Fri Mar 30, 2007 1:13 pm ] |
| Post subject: | Same here |
It loops with the suspend2 message. I am a Slackware expert, but I don't quite know where to look here to disable that. |
|
| Author: | Dale [ Fri Mar 30, 2007 4:37 pm ] |
| Post subject: | |
On real systems one needs to change the /etc/lilo.conf file. The append="....." line needs to contain a clause like: resume2=swap:/dev/hda2 noresume2 (with the hda2 replaced with your actual swap partition, of course). Then you will need to rerun lilo. |
|
| Author: | RacerX [ Fri Mar 30, 2007 11:21 pm ] |
| Post subject: | |
Thanks Dale the Fix Code: append="resume2=swap:/dev/hda2 noresume2"
lilo -v works perfect
|
|
| Author: | JoeF [ Sat Apr 07, 2007 9:58 pm ] |
| Post subject: | |
Thanks. Any chance that gets into the "pamphlet"? Or maybe it is, and I didn't see it? |
|
| Author: | Dale [ Sun Apr 08, 2007 1:00 am ] |
| Post subject: | |
Well the install scripts are supposed to do it 'right', but don't always. I'm trying to get a fix now for inclusion in the next release. |
|
| Author: | tjc [ Sun Apr 08, 2007 9:33 am ] |
| Post subject: | |
I've added something to the R5E50 upgrade hints under Known Issue #5. |
|
| Author: | JoeF [ Sun Apr 08, 2007 5:15 pm ] |
| Post subject: | |
Just another thing: Adding the "append=" line is not enough for a SCSI disk. The reason is that the driver module isn't loaded yet at the time suspend2 gets initialized. I am using a SCSI Raid, and had to load the modules at the start, in the initrd. See http://www.mysettopbox.tv/phpBB2/viewtopic.php?t=13144 |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|