Hey all,
I've been reading every forum page about the PVR-500 I know some people have been lucky at getting them to work. I'm running:
R5A16
ivtv-0.3.5f
(I aslo tried ivtv-0.3.8 and ivtv-0.3.9) all with no luck
PVR-500MCE
Seagate 200GB
Nvidia FX5200
Asus CUSL2 Mother board
256 MB RAM
Sofar what I've got is 2 channels one in colour, one in black and white, the tuner can't change the channels but everything else works fine. The TV listings from Zap2it work great however I can't figure out how to set the tuner type so that it works. I get the error:
tuner 1-0060: tuner type not set... but it does look like get set at some point.
my dmesg looks like this:
Code:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.5 (f) loading
ivtv: Linux version: 2.6.11.9-chw-2 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 9
ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 9 (level, low) -> IRQ 9
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x1130 vendor: 0x8086
ivtv: i2c attach [client=(tuner unset),ok]
tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7893786
tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3410D (type = 5)
ivtv: i2c attach [client=tveeprom[50],ok]
ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
cx25840: starting probe for adapter SMBus I801 adapter at e800 (0x0)
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
cx25840: detecting client on address 0x88
cx25840: writing init values
eth0: no IPv6 routers present
cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 13883 loaded.
cx25840: FW image md5 digest: a6f6a90a3be338cdb89d59e835798408
cx25840: FW image sha1 digest: ad2872fb98ad43b6c4afa45d239a57010edebe84
cx25840: Status: cx258433 (DEVICE_ID)
ivtv: i2c attach [client=cx25840[50],ok]
ivtv: i2c attach [client=wm8775[50],ok]
tda9885/6/7: chip found @ 0x86
ivtv: i2c attach [client=tda9887,ok]
ivtv: Encoder revision: 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create DMA stream 1 using 80 25920 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 2 using 41 50540 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create stream 4
ivtv: Setting Tuner 57
cx25840: decoder set norm NTSC
cx25840: decoder set input (6)
cx25840: Tuner Input
cx25840: set_audio_input 0
ivtv: Switching standard to NTSC.
tuner 1-0060: tuner type not set
cx25840: decoder set norm NTSC
ivtv: Initialized WinTV PVR 150, card #0
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 9 (level, low) -> IRQ 9
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x1130 vendor: 0x8086
ivtv: i2c attach [client=(tuner unset),ok]
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7893786
tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3410D (type = 5)
ivtv: i2c attach [client=tveeprom[50],ok]
cx25840: starting probe for adapter ivtv i2c driver #1 (0x10005)
cx25840: detecting client on address 0x88
cx25840: writing init values
ivtv: ivtv_enc_thread: pid = 2859, itv = 0xd16eb1a0
ivtv: ivtv_enc_vbi_thread: pid = 2860, itv = 0xd16eb1a0
cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 13883 loaded.
cx25840: FW image md5 digest: a6f6a90a3be338cdb89d59e835798408
cx25840: FW image sha1 digest: ad2872fb98ad43b6c4afa45d239a57010edebe84
cx25840: Status: cx258433 (DEVICE_ID)
ivtv: i2c attach [client=cx25840[50],ok]
ivtv: i2c attach [client=wm8775[50],ok]
tda9885/6/7: chip found @ 0x86
ivtv: i2c attach [client=tda9887,ok]
ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device, streamtype 0 minor 1
ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 1 minor 33
ivtv: Create DMA stream 1 using 80 25920 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 225
ivtv: Create DMA stream 2 using 41 50540 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 25
ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total
ivtv: Registered v4l2 device, streamtype 4 minor 65
ivtv: Create stream 4
ivtv: Setting Tuner 57
cx25840: decoder set norm NTSC
cx25840: decoder set input (6)
cx25840: Tuner Input
cx25840: set_audio_input 0
ivtv: ivtv_enc_thread: pid = 2928, itv = 0xd170e4f0
ivtv: ivtv_enc_vbi_thread: pid = 2929, itv = 0xd170e4f0
ivtv: Switching standard to NTSC.
tuner 2-0061: tuner type not set
cx25840: decoder set norm NTSC
ivtv: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================
my set_ivtv_params
Code:
#!/bin/bash
#PVR-500 TUNER 1
/usr/local/bin/ivtvctl -d /dev/video0 -u 0x3000 -f width=720,height=480 -p6
/usr/local/bin/ivtvctl -d /dev/video0 -c dnr_mode=0,dnr_temporal=4,dnr_spatial=4
/usr/local/bin/ivtvctl -d /dev/video0 -x 0
#PVR-500 TUNER 2
/usr/local/bin/ivtvctl -d /dev/video1 -u 0x3000 -f width=720,height=480 -p 6
/usr/local/bin/ivtvctl -d /dev/video1 -c dnr_mode=0,dnr_temporal=4,dnr_spatial=4
/usr/local/bin/ivtvdtl -d /dev/video1 -x 0
and my ivtv:
Code:
alias char-major-81 videodev
alias char-major-61 lirc_i2c
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
#options ivtv debug=1
#options tuner type=2
#options ivtv ivtv_std=0 tuner=2,57,57 tda9887=0,0 ivtv_debug=1
options ivtv ivtv_std=0 tuner=57,57 tda9887=0 ivtv_debug=1
options msp3400 once=1 simple=1
install ivtv /sbin/modprobe tuner; /sbin/modprobe msp3400; /sbin/modprobe saa7115; /sbin/modprobe --ignore-install ivtv
remove ivtv /sbin/modprobe -r --ignore-remove ivtv && /sbin/modprobe -r saa7115 && /sbin/modprobe -r msp3400 && /sbin/modprobe -r tuner
well sorry for the long post but I'd really appreciate any ideas I've kind of tried everything I can think of. I've reinstalled the ivtv drivers, the firmware from the CD and all the other things that other how-tos and tips I could find.
Thanks everyone!!! I'm sure this is prolly a small error somewhere in one of my files but I'm just over looking it.
Again thanks,
- Andrew -
[/code]
View unanswered posts
View active topics
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register
