LinHES Forums
http://forums.linhes.org/

Fedora Core 4 + PVR-350 = FRUSTRATION (no sound!)
http://forums.linhes.org/viewtopic.php?f=17&t=6201		 Page 1 of 1
Author:  adp1207 [ Mon Sep 26, 2005 6:27 pm ]
Post subject:  Fedora Core 4 + PVR-350 = FRUSTRATION (no sound!)
I have a P4 1.8 / 512MB RAM / 120GB Harddisk HTPC running Fedora Core 4. I also have an AIW card that I used to use (and may use for SVideo Out) and a Hauppage PVR-350 capture card.

I am following the install guide here (http://wilsonet.com/mythtv/fcmyth.php), and can capture video fine. I cannot, however, get it to capture sound. I know that the sound runs through the soundcard (which is on-board). The sound works fine when I play audio cds, but will not work when playing back video captured using the capture card. I've tried reformatting about 4 times already and have all-but not given up (which is my next step if i can't get this working).

I'd be very appreciative if someone could help me through getting the soudn working.

Below is my modprobe.conf file as well as .asoundrc file

-----BEGIN /etc/modprobe.conf-----
alias eth0 via-rhine
alias snd-card-0 snd-via82xx
options snd-card-0 index=0
options snd-via82xx index=0
remove snd-via82xx { /usr/sbin/alsactl store 0 >/dev/null 2>&1 || : ; }; /sbin/modprobe -r --ignore-remove snd-via82xx
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
alias ieee1394-controller ohci1394

# Example modprobe.conf entries for my Audigy
# Example modprobe.conf entries for my Audigy
alias snd-card-0 snd-emu10k1
install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 && /usr/sbin/alsactl restore >/dev/null 2>&1 || :
remove snd-emu10k1 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; }; /sbin/modprobe -r --ignore-remove snd-emu10k1

# ivtv modules setup
alias char-major-81 ivtv
alias char-major-81-0 ivtv
alias tveeprom tveeprom-ivtv
alias msp3400 msp3400-ivtv
install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb

-----END /etc/modprobe.conf-----


---BEGIN /home/mythtv/.asoundrc --------
# Override the default output used by ALSA.
# If you do not override the default, your default
# device is identical to the (unmixed) analog device
# shown below. If you prefer mixed and/or digital
# output, uncomment the appropriate four lines below
# (only one slave.pcm line).
### Currently set w/digital-hw as the default output,
### comment out this entire section to use unmixed
### analog as your default
### -jarod
pcm.!default {
type plug
## Uncomment the following to use mixed analog by default
# slave.pcm "dmix-analog"
## Uncomment the following to use unmixed digital by default
slave.pcm "digital-hw"
## Uncomment the following to use mixed digital by default
# slave.pcm "dmix-digital"
}

# Alias for analog output on the Audigy (hw:0,0)
# - This is identical to the device named "default"--which
# always exists and refers to hw:0,0 (unless overridden)
# - Therefore, we can specify "hw:0,0", "default", or "analog"
# to access analog output on the Audigy
pcm.analog {
type plug
slave.pcm "analog-hw"
}

# Control device (mixer, etc.) for the Audigy card
ctl.analog {
type hw
card 0
}

# Alias for (rate-converted) mixed analog output on the
# Audigy (hw:0,0)
# - This will accept audio input--regardless of rate--and
# convert to the rate required for the dmix plugin
# (in this case 48000Hz)
pcm.mixed-analog {
type plug
slave.pcm "dmix-analog"
}

# Control device (mixer, etc.) for the Audigy card
ctl.mixed-analog {
type hw
card 0
}

# Alias for (rate-converted) digital (S/PDIF) output on the
# Audigy (hw:0,0)
# - This will accept audio input--regardless of rate--and
# convert to the rate required for the S/PDIF hardware
# (in this case 48000Hz)
pcm.digital {
type plug
slave.pcm "digital-hw"
}

# Control device (mixer, etc.) for the Audigy card
ctl.digital {
type hw
card 0
}

# Alias for mixed (rate-converted) digital (S/PDIF) output on the
# Audigy (hw:0,0)
# - This will accept audio input--regardless of rate--and
# convert to the rate required for the S/PDIF hardware
# (in this case 48000Hz)
pcm.mixed-digital {
type plug
slave.pcm "dmix-digital"
}

# Control device (mixer, etc.) for the Audigy card
ctl.mixed-digital {
type hw
card 0
}

# The following devices are not useful by themselves. They
# require specific rates, channels, and formats. Therefore,
# you probably do not want to use them directly. Instead use
# of of the devices defined above.

# Alias for analog output on the Audigy (hw:0,0)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.analog-hw {
type hw
card 0
# The default value for device is 0, so no need to specify
}

# Control device (mixer, etc.) for the Audigy card
ctl.analog-hw {
type hw
card 0
}

# Alias for digital (S/PDIF) output on the Audigy (hw:0,0)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.digital-hw {
type hw
card 0
device 0
}

# Control device (mixer, etc.) for the Audigy card
ctl.digital-hw {
type hw
card 0
}

# Direct software mixing plugin for analog output on
# the Audigy (hw:0,0)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.dmix-analog {
type dmix
ipc_key 1234
slave {
pcm "analog-hw"
period_time 0
period_size 1024
buffer_size 4096
rate 48000
}
}

# Control device (mixer, etc.) for the Audigy card
ctl.dmix-analog {
type hw
card 0
}

# Direct software mixing plugin for digital (S/PDIF) output
# on the Audigy (hw:0,0)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.dmix-digital {
type dmix
ipc_key 1235
slave {
pcm "digital-hw"
period_time 0
period_size 1024
buffer_size 4096
rate 48000
}
}

# Control device (mixer, etc.) for the Audigy card
ctl.dmix-digital {
type hw
card 0
}
---END /home/mythtv/.asoundrc ------
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/