| Author |
Message |
|
diblasio
|
 Posted: Fri Oct 20, 2006 9:34 pm |
|
|
Joined: Tue Apr 11, 2006 6:31 pm
Posts: 31
Location:
Austin, TX
|
I'm having trouble getting my Hauppauge pvr 150 working. Here's my dmesg.
Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (tagged release) loading
ivtv: Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 19
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 2-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
eth0: no IPv6 routers present
cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
tveeprom 2-0050: Hauppauge model 26132, rev G1B2, serial# 9544219
tveeprom 2-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is CX25841 (idx 35)
tveeprom 2-0050: decoder processor is CX25841 (idx 28)
tveeprom 2-0050: has no radio, has IR remote
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 2-0061: tuner type not set
tuner 2-0061: tuner type not set
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
lirc_pvr150: chip found with RX and TX
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_pvr150: firmware of size 209327 loaded
lirc_pvr150: 575 codesets loaded
lirc_pvr150: Hauppauge PVR-150 IR blaster: firmware version 1.3.0
tuner 2-0061: tuner type not set
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
tuner 2-0061: tuner type not set
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 20
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
tuner 2-0061: tuner type not set
Last edited by diblasio on Mon Oct 23, 2006 5:29 pm, edited 1 time in total.
|
|
| Top |
|
 |
|
tjc
|
Posted: Sat Oct 21, 2006 8:20 am |
|
|
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location:
Arlington, MA
|
|
| Top |
|
|
|
ALF
|
Posted: Sat Oct 21, 2006 9:44 pm |
|
|
Joined: Fri Oct 13, 2006 2:55 am
Posts: 17
|
http://www.knoppmythwiki.org/index.php? ... ptureCards
I just had this issue earlier. I saw "ALSA Sound" at the top of the page and figured the rest of the page was going to be how to fix sound issues.
Turns out there's a second part.
Read towards the bottom and it'll help you solve the issue.
|
|
| Top |
|
|
|
Gothmolly
|
Posted: Sat Nov 11, 2006 11:48 pm |
|
|
Joined: Sat Nov 11, 2006 11:39 pm
Posts: 2
|
|
| Top |
|
|
|
tjc
|
Posted: Sun Nov 12, 2006 11:24 am |
|
|
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location:
Arlington, MA
|
|
Who? People like you, who don't recognize a polite informative tutorial response with a request for people to _please_ try to avoid flooding the forums with FAQs which have been answered a dozen times in the last week, when they see one.
If you read a rebuke into _this_ repsonse you're probably right, but it's pretty mild one. Reading it into the original however is a complete miss. Spend some time reading the forums before you start posting. Knowing who you're talking to and what their writing style is will give you a better read on intent. Knowing who uses hyperbole or irony as a device in their writing, who is very terse or laconic, who writes like an engineer (guilty) or a school teacher, ... You may also notice that there was no profanity or abusive language in either of these postings, and that I generally use complete, well formed sentences.
I happen to answer _a lot_ of questions around here. I read practically every posting. I know when someone has spammed the forums by posting the same question under a half dozen different topics, or just isn't grasping what people are telling them. I know when the same question comes up again and again. I often go out of my way to help someone track down a particularly bizarre problem and spend days or even weeks going back and forth until it's fixed or they give up. I also often just post a link to the relevant information or a note to search for certain terms.
Sometimes I post a message like my original response in this thread, which is basically a compressed tutorial on how to fish for yourself rather than waiting for someone to give you the leftovers from the catch of the day. When I take the extra time to do this (instead of just posting the link) I'm usually trying to not only help the current poster, but also to provide a set of information and resources for future newbies.
|
|
| Top |
|
|
|
strick1226
|
Posted: Mon Nov 13, 2006 8:45 pm |
|
|
Joined: Thu Dec 15, 2005 12:20 pm
Posts: 102
|
|
OK, I have one of these new PVR-150's and I'm having the same issue.
But the modification to the /etc/modules.conf does not work.
ivtv 0.7.1 is detecting a TCL M2523_5N_E .
I have tried manually adding "options ivtv tuner=50" to /etc/modules.conf, but I still see this:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.1 (tagged release) loading
ivtv: Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
tveeprom 1-0050: Hauppauge model 26132, rev G1B2, serial# 9545781
tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is CX25841 (idx 35)
tveeprom 1-0050: decoder processor is CX25841 (idx 28)
tveeprom 1-0050: has no radio, has IR remote
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 1-0061: tuner type not set
tuner 1-0061: tuner type not set
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
nvidia: module license 'NVIDIA' taints kernel.
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
tuner 1-0061: tuner type not set
This is on a installed-from-scratch R5D1 install. nVidia FX5200 connected to an NTSC TV via composite, and the PVR-150 getting analog cable on the tuner input with coax.
Works great with a pair of older PVR-150's, but I can *NOT* get this to work.
Any other ideas?
Thanks in advance!
_________________
R5.5
p4/3.0 GHz
2GB PC3200
Abit IC7-G
3x Seagate 7200.10 SATA (raid1 /, raid5 /myth)
eVGA FX-5500 AGP
3x PVR-150 (model 1045)
MCEUSB2 remote w/Philips USB transceiver
|
|
| Top |
|
|
|
slowtolearn
|
Posted: Tue Nov 14, 2006 1:08 pm |
|
|
Joined: Wed Nov 16, 2005 8:55 pm
Posts: 1381
Location:
Farmington, MI USA
|
strick1226 wrote: But the modification to the /etc/modules.conf does not work.
Typo? That should be modprobe.conf
|
|
| Top |
|
|
|
strick1226
|
Posted: Tue Nov 14, 2006 1:22 pm |
|
|
Joined: Thu Dec 15, 2005 12:20 pm
Posts: 102
|
I *think* I put it in the right file... hmmm... let me check when I get home.
Wow, that would be embarrassing. 
Thanks for the suggestion!
_________________
R5.5
p4/3.0 GHz
2GB PC3200
Abit IC7-G
3x Seagate 7200.10 SATA (raid1 /, raid5 /myth)
eVGA FX-5500 AGP
3x PVR-150 (model 1045)
MCEUSB2 remote w/Philips USB transceiver
|
|
| Top |
|
|
|
slowtolearn
|
Posted: Tue Nov 14, 2006 8:19 pm |
|
|
Joined: Wed Nov 16, 2005 8:55 pm
Posts: 1381
Location:
Farmington, MI USA
|
strick1226 wrote: I *think* I put it in the right file... hmmm... let me check when I get home. Wow, that would be embarrassing. Thanks for the suggestion! Heh, you certainly wouldn't be the first one here on this forum to make a mistake!
Let us know if that was the issue...
|
|
| Top |
|
|
|
strick1226
|
Posted: Wed Nov 15, 2006 10:45 am |
|
|
Joined: Thu Dec 15, 2005 12:20 pm
Posts: 102
|
Holy crap, that was it!
Thanks for pointing that out!!!
_________________
R5.5
p4/3.0 GHz
2GB PC3200
Abit IC7-G
3x Seagate 7200.10 SATA (raid1 /, raid5 /myth)
eVGA FX-5500 AGP
3x PVR-150 (model 1045)
MCEUSB2 remote w/Philips USB transceiver
|
|
| Top |
|
|
|
slowtolearn
|
Posted: Wed Nov 15, 2006 11:02 am |
|
|
Joined: Wed Nov 16, 2005 8:55 pm
Posts: 1381
Location:
Farmington, MI USA
|
|
| Top |
|
|
View unanswered posts
View active topics
KnoppMyth 
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register