I have an nVidiia MX 440 video card with S-Video out to a Hitachi HDTV. I also have a computer monitor hooked up to the VGA port. I cannot seem to get the svideo out from the video card to work with the TV. All I get on the TV screen is a scrambled mess that is obviously not refreshing correctly. I have read about the XF86Config-4 file and made some modifications as suggested, but still can't seem to get it working.

What should I modifiy in my XF86Config-4 file to modify the TV-out on my video card? Do I modify the "Device" Section or the "Monitor" xection to modify the Svideo out on the TV card? Here is the file...

Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "PS/2 Mouse" "CorePointer"
# Serial Mouse not detected
# USB Mouse not detected
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"

EndSection

Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
FontPath "/usr/X11R6/lib/X11/fonts/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/misc"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo"
FontPath "/usr/X11R6/lib/X11/fonts/PEX"
# Additional fonts: Locale, Gimp, TTF...
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic"
# FontPath "/usr/X11R6/lib/X11/fonts/latin2/75dpi"
# FontPath "/usr/X11R6/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
FontPath "/usr/X11R6/lib/X11/fonts/Type1"
FontPath "/usr/share/fonts/ttf/western"
FontPath "/usr/share/fonts/ttf/decoratives"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/latex-ttf-fonts"
FontPath "/usr/X11R6/lib/X11/fonts/defoma/CID"
FontPath "/usr/X11R6/lib/X11/fonts/defoma/TrueType"
EndSection

Section "Module"
Load "ddc" # ddc probing of monitor
Load "GLcore"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "speedo"
Load "type1"
Load "freetype"
Load "record"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"

EndSection

Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

# Auto-generated by KNOPPIX mkxf86config


Section "Device"
Identifier "Videocard0"
Driver "nvidia"
VendorName "AOpen"
BoardName "nVidia GeForce 4 MX 440"
Option "RenderAccel" "1"
Option "NvAGP" "1"
Option "NoDDC" "1"
# TV Out Setup
Option "TwinView"
Option "TwinViewOrientation" "Clone"
Option "ConnectedMonitor" "CRT,TV"
Option "SecondMonitorHorizSync" "36.5-37.9"
Option "SecondMonitorVertRefresh" "60.0"
Option "MetaModes" "1024x768, 1024x768; 800x600, 800,600; 640x480, 640x480;"
Option "TVStandard" "NTSC-M"
Option "TVOutFormat" "SVIDEO"
Option "TVOverScan" "0.5"
EndSection



Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "true"
Option "ConnectedMonitor" "TV"
VendorName "OQI"
ModelName "OQI4433"
# HorizSync 30.0 - 50.0 # Warning: This may fry very old Monitors
HorizSync 30 - 50 # Warning: This may fry old Monitors

VertRefresh 60 # Very conservative. May flicker.
# These are the DDC-probed settings reported by your monitor.
# 1280x1024, 75.0Hz; hfreq=79.98, vfreq=75.03
ModeLine "1280x1024" 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
# 1152x864, 75.0Hz; hfreq=67.50, vfreq=75.00
ModeLine "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
# 1024x768, 85.0Hz; hfreq=68.68, vfreq=85.00
ModeLine "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
# 1024x768, 75.0Hz; hfreq=60.02, vfreq=75.03
ModeLine "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
# 1024x768, 70.0Hz; hfreq=56.48, vfreq=70.07
ModeLine "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
# 1024x768, 60.0Hz; hfreq=48.36, vfreq=60.00
ModeLine "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
# 800x600, 85.0Hz; hfreq=53.67, vfreq=85.06
ModeLine "800x600" 56.25 800 832 896 1048 600 601 604 631 +hsync +vsync
# 800x600, 75.0Hz; hfreq=46.88, vfreq=75.00
ModeLine "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
# 800x600, 60.0Hz; hfreq=37.88, vfreq=60.32
ModeLine "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
# 800x600, 56.0Hz; hfreq=35.16, vfreq=56.25
ModeLine "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
# 640x480, 85.0Hz; hfreq=43.27, vfreq=85.01
ModeLine "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
# 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
ModeLine "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
# 640x480, 72.0Hz; hfreq=37.86, vfreq=72.81
ModeLine "640x480" 31.50 640 656 696 816 480 481 484 504 -hsync -vsync
# 640x480, 60.0Hz; hfreq=31.47, vfreq=59.94
ModeLine "640x480" 25.17 640 648 744 784 480 482 484 509 -hsync -vsync
EndSection

Section "Device"
### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
Option "sw_cursor"
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Identifier "Card0"
# The following line is auto-generated by KNOPPIX mkxf86config
Driver "nv"
VendorName "All"
BoardName "All"
# BusID "PCI:1:0:0"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16
SubSection "Display"
Depth 1
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection

Section "DRI"
Mode 0666
EndSection

well I've never tried to use twinview, but as I recall you have to change the mode under your screens section to reflect the metamode you want to use. You would probably have an easier time if you just used tvout and forgot about twinview.

Check out the XF86Config examples that I posted under "Tier 2" earlier today.