View unanswered posts    View active topics

All times are UTC - 6 hours





Post new topic Reply to topic  [ 1 post ] 
Print view Previous topic   Next topic  
Author Message
Search for:
PostPosted: Sat Jul 28, 2007 6:40 am 
Offline
Joined: Wed Apr 12, 2006 3:05 pm
Posts: 252
Location: GA, USA
I'm working on a fresh install of R5F1. I previously had been using a PVR 250 and added a PVR 500MCE when I decided to perform a clean install. After auto-install finished and I tried to setup the tuners, I saw that only one of the PVR 500's tuners was detected. I tried upgrading to ivtv 0.10.5 and got the same results. Here's my dmesg output:
Code:
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.10.5 (tagged release) loading
ivtv:  Linux version: 2.6.18-chw-13 SMP preempt mod_unload 586 gcc-4.1
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
tveeprom 1-0050: Hauppauge model 32062, rev C199, serial# 8552317
tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is MSP3445 (idx 12)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-250
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0)
msp3400 1-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #0)
ivtv0: Registered device video0 for encoder MPEG (4 MB)
ivtv0: Registered device video32 for encoder YUV (2 MB)
ivtv0: Registered device vbi0 for encoder VBI (1 MB)
ivtv0: Registered device video24 for encoder PCM audio (1 MB)
tuner 1-0061: type set to 50 (TCL 2002N)
ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected Hauppauge card (cx23416 based)
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
ivtv1: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Retry loading firmware
ivtv1: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Error initializing firmware
ivtv1: Error -19 on initialization
ivtv:  ======================  NEXT CARD  ======================
ivtv2: Autodetected Hauppauge card (cx23416 based)
ivtv2: Unreasonably low latency timer, setting to 64 (was 32)
ivtv2: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv2: Encoder revision: 0x02060039
tuner 2-0043: chip found @ 0x86 (ivtv i2c driver #2)
tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner)
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #2)
tveeprom 2-0050: Hauppauge model 23552, rev E692, serial# 10303535
tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has radio, has no IR receiver, has no IR transmitter
ivtv2: Correcting tveeprom data: no radio present on second unit
ivtv2: Autodetected WinTV PVR 500 (unit #2)
cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #2)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #2)
ivtv2: Registered device video2 for encoder MPEG (4 MB)
ivtv2: Registered device video34 for encoder YUV (2 MB)
ivtv2: Registered device vbi2 for encoder VBI (1 MB)
ivtv2: Registered device video26 for encoder PCM audio (1 MB)
tuner 2-0061: type set to 57 (Philips FQ1236A MK4)
ivtv2: Initialized WinTV PVR 500 (unit #2), card #2
ivtv:  ====================  END INIT IVTV  ====================
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-1/1-0018/ir0 [ivtv i2c driver #0]


I've done a lot of searching, and most solutions point to problems with the firmware revision, etc. However, since one tuner is detected I'm thinking the other tuner is plain bad. Is there any possibility there's a software fix to this problem or do I need a new PVR 500? I'm hoping I don't have to get another one because returning things to newegg from an APO address is a pain.


Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 


All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 71 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu