on R5f27, after addressing another separate ir remote issue i rebooted the box and now X wont load.

the system is switching into tv-out and console is being displayed on the NTSC TV via the pvr350 tv out before x loads. Then, when x tries to load it pukes

Initially when I installed, using a dell FP2001 monitor, I said 'yes' when asked to enable tv-out on the pvr350. I then finished the rest of mythtv-setup, restarted frontend and tv-out took over no problems.

Myth has been running fine for about a month and I dont remember rebooting at all after the initial install, but i might have..

anyway, this time around when I rebooted X reports:

Screen 0 deleted because of no matching config section
Device(s) detected, but non match those in the config file.
Fatal server error:
no screens found


I assume this is because x doesnt know wtf its doing with my NTSC TV..
its probably looking for my Dell monitor, which is attached. But again, tv-out on the pvr350 is taking precedence, and x keeps puking.

Below are 2 versions of xorg.conf. One pushing the pvr350's tv out (not working), and the other that is working with my dell monitor..


Using the 2nd conf below I can get the myth interface to work via my dell monitor.. console is still running out of the PVR350, but when i watch a recorded program, the dell monitor goes blank and the NTSC displays the video, then when I back out of the video feed, myth switches back to the Dell monitor(vga)

WEIRD AND ANNOYING!

any help is much appreciated. Thanks!

-----------------------------------------------------
/etc/X11/xorg.conf
-----------------------------------------------------
Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "TV Screen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
# PS/2 Mouse not detected
# Serial Mouse not detected
InputDevice "USB Mouse" "CorePointer"
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"

EndSection

Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc:unscaled"
FontPath "/usr/share/fonts/X11/75dpi:unscaled"
FontPath "/usr/share/fonts/X11/100dpi:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/Speedo"
FontPath "/usr/share/fonts/X11/PEX"
# Additional fonts: Locale, Gimp, TTF...
FontPath "/usr/share/fonts/X11/cyrillic"
# FontPath "/usr/share/fonts/X11/latin2/75dpi"
# FontPath "/usr/share/fonts/X11/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/latex-ttf-fonts"
EndSection

Section "Module"
# Comments: see http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=346408
Load "dbe" # Double Buffering Extension, very important.
Load "dri" # This shouldn't be available choice if user has selected driver vga, vesa or nv.
Load "glx" # GLX Extension.
Load "freetype" # Freetype fonts.
Load "type1" # Type 1 fonts
Load "record" # Developer extension, usually not needed
# Load "extmod" # This is okay, but if you look into "man xorg.conf" you'll find option NOT to include DGA extension with extmod, and for a good reason.. DGA causes instability as it access videoram without consulting X about it.
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
# Load "speedo" # Speedo fonts, this module doesn't exist in Xorg 7.0.17
# The following are deprecated/unstable/unneeded in Xorg 7.0
# Load "ddc" # ddc probing of monitor, this should be never present, as it gets automatically loaded.
# Load "GLcore" # This should be never present, as it gets automatically loaded.
# Load "bitmap" # Should be never present, as it gets automatically loaded. This is a font module, and loading it in xorg.conf makes X try to load it twice.
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"

EndSection

Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

# Auto-generated by KNOPPIX mkxf86config




Section "Monitor"
Identifier "NTSC Monitor"
HorizSync 30-68
VertRefresh 50-120
Mode "720x480"
# D: 34.563 MHz, H: 37.244 kHz, V: 73.897 Hz
DotClock 34.564
HTimings 720 752 840 928
VTimings 480 484 488 504
Flags "-HSync" "-VSync"
EndMode
EndSection

Section "Device"
Identifier "Hauppauge PVR 350 iTVC15 Framebuffer"
Driver "ivtv"

### change fb1 to whatever number you got in the previous section
Option "fbdev" "/dev/fb1"
Option "VideoOverlay" "on"
Option "XVideo" "1"

### change the busid to whatever is reported by lspci. Note that
### output of lspci is hex, so add a preceding "0x" to the BusID
BusID "PCI:0:20:0"

# Screen 0
EndSection

Section "Screen"
Identifier "TV Screen"
Device "Hauppauge PVR 350 iTVC15 Framebuffer"
Monitor "NTSC Monitor"
DefaultDepth 24
DefaultFbbpp 32
Subsection "Display"
Depth 24
FbBpp 32
Modes "720x480"
EndSubsection
EndSection

Section "DRI"
Mode 0666
EndSection
-----------------------------------------------------------




-----------------------------------------------------
/etc/X11/xorg.conf (the one i used when installing knoppmyth initally)
-----------------------------------------------------
Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
# PS/2 Mouse not detected
# Serial Mouse not detected
InputDevice "USB Mouse" "CorePointer"
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"

EndSection

Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc:unscaled"
FontPath "/usr/share/fonts/X11/75dpi:unscaled"
FontPath "/usr/share/fonts/X11/100dpi:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/Speedo"
FontPath "/usr/share/fonts/X11/PEX"
# Additional fonts: Locale, Gimp, TTF...
FontPath "/usr/share/fonts/X11/cyrillic"
# FontPath "/usr/share/fonts/X11/latin2/75dpi"
# FontPath "/usr/share/fonts/X11/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/latex-ttf-fonts"
EndSection

Section "Module"
# Comments: see http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=346408
Load "dbe" # Double Buffering Extension, very important.
Load "dri" # This shouldn't be available choice if user has selected driver vga, vesa or nv.
Load "glx" # GLX Extension.
Load "freetype" # Freetype fonts.
Load "type1" # Type 1 fonts
Load "record" # Developer extension, usually not needed
# Load "extmod" # This is okay, but if you look into "man xorg.conf" you'll find option NOT to include DGA extension with extmod, and for a good reason.. DGA causes instability as it access videoram without consulting X about it.
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
# Load "speedo" # Speedo fonts, this module doesn't exist in Xorg 7.0.17
# The following are deprecated/unstable/unneeded in Xorg 7.0
# Load "ddc" # ddc probing of monitor, this should be never present, as it gets automatically loaded.
# Load "GLcore" # This should be never present, as it gets automatically loaded.
# Load "bitmap" # Should be never present, as it gets automatically loaded. This is a font module, and loading it in xorg.conf makes X try to load it twice.
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"

EndSection

Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection

Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

# Auto-generated by KNOPPIX mkxf86config

Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "false"
VendorName "MTC"
ModelName "MTC0000"
HorizSync 31 - 60 # DDC-probed
VertRefresh 56 - 75 # DDC-probed
# These are the DDC-probed settings reported by your monitor.
# 1280x1024, 75.0Hz; hfreq=79.98, vfreq=75.03
ModeLine "1280x1024" 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
# 1024x768, 75.0Hz; hfreq=60.02, vfreq=75.03
ModeLine "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
# 1024x768, 70.0Hz; hfreq=56.48, vfreq=70.07
ModeLine "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
# 800x600, 75.0Hz; hfreq=46.88, vfreq=75.00
ModeLine "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
# 800x600, 60.0Hz; hfreq=37.88, vfreq=60.32
ModeLine "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
# 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
ModeLine "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
# 640x480, 72.0Hz; hfreq=37.86, vfreq=72.81
ModeLine "640x480" 31.50 640 656 696 816 480 481 484 504 -hsync -vsync
# 640x480, 60.0Hz; hfreq=31.47, vfreq=59.94
ModeLine "640x480" 25.17 640 648 744 784 480 482 484 509 -hsync -vsync
# Extended modelines with GTF timings
# 640x480 @ 100.00 Hz (GTF) hsync: 50.90 kHz; pclk: 43.16 MHz
ModeLine "640x480" 43.16 640 680 744 848 480 481 484 509 -HSync +Vsync
# 768x576 @ 60.00 Hz (GTF) hsync: 35.82 kHz; pclk: 34.96 MHz
ModeLine "768x576" 34.96 768 792 872 976 576 577 580 597 -HSync +Vsync
# 768x576 @ 72.00 Hz (GTF) hsync: 43.27 kHz; pclk: 42.93 MHz
ModeLine "768x576" 42.93 768 800 880 992 576 577 580 601 -HSync +Vsync
# 768x576 @ 75.00 Hz (GTF) hsync: 45.15 kHz; pclk: 45.51 MHz
ModeLine "768x576" 45.51 768 808 888 1008 576 577 580 602 -HSync +Vsync
# 768x576 @ 85.00 Hz (GTF) hsync: 51.42 kHz; pclk: 51.84 MHz
ModeLine "768x576" 51.84 768 808 888 1008 576 577 580 605 -HSync +Vsync
# 768x576 @ 100.00 Hz (GTF) hsync: 61.10 kHz; pclk: 62.57 MHz
ModeLine "768x576" 62.57 768 816 896 1024 576 577 580 611 -HSync +Vsync
# 800x600 @ 100.00 Hz (GTF) hsync: 63.60 kHz; pclk: 68.18 MHz
ModeLine "800x600" 68.18 800 848 936 1072 600 601 604 636 -HSync +Vsync
# 1024x768 @ 100.00 Hz (GTF) hsync: 81.40 kHz; pclk: 113.31 MHz
ModeLine "1024x768" 113.31 1024 1096 1208 1392 768 769 772 814 -HSync +Vsync
# 1152x864 @ 60.00 Hz (GTF) hsync: 53.70 kHz; pclk: 81.62 MHz
ModeLine "1152x864" 81.62 1152 1216 1336 1520 864 865 868 895 -HSync +Vsync
# 1152x864 @ 85.00 Hz (GTF) hsync: 77.10 kHz; pclk: 119.65 MHz
ModeLine "1152x864" 119.65 1152 1224 1352 1552 864 865 868 907 -HSync +Vsync
# 1152x864 @ 100.00 Hz (GTF) hsync: 91.50 kHz; pclk: 143.47 MHz
ModeLine "1152x864" 143.47 1152 1232 1360 1568 864 865 868 915 -HSync +Vsync
# 1280x960 @ 72.00 Hz (GTF) hsync: 72.07 kHz; pclk: 124.54 MHz
ModeLine "1280x960" 124.54 1280 1368 1504 1728 960 961 964 1001 -HSync +Vsync
# 1280x960 @ 75.00 Hz (GTF) hsync: 75.15 kHz; pclk: 129.86 MHz
ModeLine "1280x960" 129.86 1280 1368 1504 1728 960 961 964 1002 -HSync +Vsync
# 1280x960 @ 100.00 Hz (GTF) hsync: 101.70 kHz; pclk: 178.99 MHz
ModeLine "1280x960" 178.99 1280 1376 1520 1760 960 961 964 1017 -HSync +Vsync
# 1280x1024 @ 100.00 Hz (GTF) hsync: 108.50 kHz; pclk: 190.96 MHz
ModeLine "1280x1024" 190.96 1280 1376 1520 1760 1024 1025 1028 1085 -HSync +Vsync
# 1400x1050 @ 60.00 Hz (GTF) hsync: 65.22 kHz; pclk: 122.61 MHz
ModeLine "1400x1050" 122.61 1400 1488 1640 1880 1050 1051 1054 1087 -HSync +Vsync
# 1400x1050 @ 72.00 Hz (GTF) hsync: 78.77 kHz; pclk: 149.34 MHz
ModeLine "1400x1050" 149.34 1400 1496 1648 1896 1050 1051 1054 1094 -HSync +Vsync
# 1400x1050 @ 75.00 Hz (GTF) hsync: 82.20 kHz; pclk: 155.85 MHz
ModeLine "1400x1050" 155.85 1400 1496 1648 1896 1050 1051 1054 1096 -HSync +Vsync
# 1400x1050 @ 85.00 Hz (GTF) hsync: 93.76 kHz; pclk: 179.26 MHz
ModeLine "1400x1050" 179.26 1400 1504 1656 1912 1050 1051 1054 1103 -HSync +Vsync
# 1400x1050 @ 100.00 Hz (GTF) hsync: 111.20 kHz; pclk: 214.39 MHz
ModeLine "1400x1050" 214.39 1400 1512 1664 1928 1050 1051 1054 1112 -HSync +Vsync
# 1600x1200 @ 100.00 Hz (GTF) hsync: 127.10 kHz; pclk: 280.64 MHz
ModeLine "1600x1200" 280.64 1600 1728 1904 2208 1200 1201 1204 1271 -HSync +Vsync
# 1920x1200 @ 60.00 Hz (GTF) hsync: 74.52; pclk: 193.16 MHz
Modeline "1920x1200" 193.16 1920 2048 2256 2592 1200 1201 1204 1242 -HSync +HSync
EndSection

Section "Device"
### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
#Option "sw_cursor"
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Identifier "Card0"
# The following line is auto-generated by KNOPPIX mkxf86config
Driver "via"
VendorName "All"
BoardName "All"
# BusID "PCI:1:0:0"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 24
SubSection "Display"
Depth 1
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection

Section "DRI"
Mode 0666
EndSection
--------------------------------------------------------

Probably set to the incorrect fb device, try /dev/fb0. See tjc's R5F27 Hints and Tips for other possibilities, as well as searching the forums for PVR-350.

word.

That worked, everything is running good.. i appreciate the help!