LinHES Forums
http://forums.linhes.org/

Streamzap quit working
http://forums.linhes.org/viewtopic.php?f=2&t=19171
Page 1 of 1

Author:  krmiller [ Mon Nov 03, 2008 9:42 pm ]
Post subject:  Streamzap quit working

I have a streamzap that worked great in the past. When I upgraded to 5.5 it worked fine for about two weeks and then stopped. I have rebooted, unplugged the reciever...used a different receiver and no luck. When I searched through /var/logs I found nothing. Any ideas?


Below is a sample of my logs

lircd:Nov 2 21:21:16 mythtv lircd: accepted new client on /dev/lircd
lircd:Nov 2 22:37:14 mythtv lircd: removed client
lircd:Nov 2 22:37:21 mythtv lircd: accepted new client on /dev/lircd
lircd:Nov 2 22:38:02 mythtv lircd: caught signal
lircd:Nov 2 22:39:05 mythtv lircd: lircd(all) ready
lircd:Nov 2 22:40:15 mythtv lircd: accepted new client on /dev/lircd
messages.0:Nov 2 22:39:04 mythtv kernel: lirc_dev: IR Remote Control driver registered, major 61
messages.0:Nov 2 22:39:04 mythtv kernel: lirc_streamzap[-1]: Streamzap, Inc. Streamzap Remote Control on usb4:2 attached
messages.0:Nov 2 22:39:04 mythtv kernel: lirc_dev: lirc_register_plugin: sample_rate: 0
messages.0:Nov 2 22:39:04 mythtv kernel: usbcore: registered new interface driver lirc_streamzap
messages.0:Nov 2 22:39:04 mythtv kernel: lirc_streamzap $Revision: 1.25 $ registered

Author:  manicmike [ Tue Nov 04, 2008 1:52 am ]
Post subject:  Re: Streamzap quit working

Hate to ask the very obvious, but are the batteries known to be good?

Mike

Author:  nmcaullay [ Tue Nov 04, 2008 6:04 pm ]
Post subject: 

Wih the benefit of knowing 0% about the streamzap gear, i thought i'd post anyway just incase. My remote worked 100% in R5F27, but intermittently in R5.5... was due to udev, and random assignment of ID's on boot. Could it be caused by anything like that? New cards in system, changing ID's?

Probably not, thought i'd try to help though

Nathan

Author:  jimdoc [ Tue Nov 04, 2008 8:28 pm ]
Post subject: 

As another point of reference, I've had no problems with my Streamzap in R5.5.

Originally as an upgrade from R5E50, then a clean R5.5 install (after a complete hard drive failure).

Author:  krmiller [ Tue Nov 04, 2008 11:52 pm ]
Post subject: 

I double checked my batteries and know they are working because I can see the LED in the IR receiver blink when I push a button. How to I go about checking if the udev id is the issue?

My system is a fresh 5.5 install. I did add new hardware when I initially installed but the streamzap worked after the initial install. It stopped working several weeks later without any hardware changes.

Author:  manicmike [ Wed Nov 05, 2008 2:15 am ]
Post subject: 

krmiller wrote:
I double checked my batteries and know they are working because I can see the LED in the IR receiver blink when I push a button.


That's not a good test. The receiver will blink unless the batteries are absolutely dead. Try a fresh set of batteries.

Mike

Author:  krmiller [ Wed Nov 05, 2008 10:53 pm ]
Post subject: 

Ok...everyone can call me stupid...It was the batteries. I made the bad assumption that if the receiver was blinking that the batteries were good. Thanks for the tips..

Author:  nmcaullay [ Wed Nov 05, 2008 10:55 pm ]
Post subject: 

i would call you stupid, but i've been quilty of far worse :)

Author:  manicmike [ Thu Nov 06, 2008 12:42 am ]
Post subject: 

krmiller wrote:
Ok...everyone can call me stupid...It was the batteries. .


You aren't stupid: Everyone would have thought like you did.

Mike

Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/