| LinHES Forums http://forums.linhes.org/ |
|
| R6 serial IR Balaster Help http://forums.linhes.org/viewtopic.php?f=2&t=20510 |
Page 1 of 1 |
| Author: | ssbn [ Wed Nov 11, 2009 12:13 pm ] |
| Post subject: | R6 serial IR Balaster Help |
Hi, I just installed the newest r6 and cant seem to get the irblaster working on r6. I think my problem is finding what ttys port to use. This is my sustemconfig #IR settings file #IR settings Remotetype="mceusb" ReceiverType="Default" HostLircWait="" ReceiverSerialport="ttyS0" HostTransmitproto_1="motorola_dsr315" HostTransmitproto_2="none" HostTransmitproto_3="none" HostTransmitproto_4="none" HostBlasterType="Serial" HostSerialPort_blasterlirc="ttyS1" Hostnumblaster="1" rootSSH="1" From this when i type in ;irsend SEND_ONCE Motorola_dsr_series power the device wont power off. My question is is there a way to send the signal from command line to a port just in case i have the wrong one or a way to identify what one is active. this is what i get with dmesg | grep lirc lirc_dev: IR Remote Control driver registered, major 61 lirc_mod_mce: Input driver for Microsoft MCE 2005 keyboard v0.1.5 lirc_mod_mce: Florian Demski lirc_dev: lirc_register_plugin: sample_rate: 0 lirc_mod_mce[2]: SMK eHome Infrared Transceiver on usb2:2 usbcore: registered new interface driver lirc_mod_mce lirc_serial: auto-detected active low receiver lirc_dev: lirc_register_plugin: sample_rate: 0 |
|
| Author: | ssbn [ Wed Nov 11, 2009 12:35 pm ] |
| Post subject: | |
after a bit more reading it looks like my irblaster may be ttys0 that may be com1 but looking at irsettings #IR settings Remotetype="mceusb" ReceiverType="mceusb" HostLircWait="" ReceiverSerialport="ttyS0" HostTransmitproto_1="motorola_dsr315" HostTransmitproto_2="none" HostTransmitproto_3="none" HostTransmitproto_4="none" HostBlasterType="Serial" HostSerialPort_blasterlirc="ttyS0" Hostnumblaster="1" rootSSH="1" Receiverserialport is using that. I have a mce usb receiver that is working. How do find out they my only serial port is? In my bios the com port is showing as 3f8/irq4 |
|
| Author: | ssbn [ Wed Nov 11, 2009 1:48 pm ] |
| Post subject: | |
More info it looks like my serial port is ttys0. dmesg | grep tty Kernel command line: root=/dev/disk/by-uuid/ee588e0c-5140-483e-a523-be60520be448 ro init=/sbin/runit quiet vga=0x314 splash=silent,theme:linhes console=tty1 console [tty1] enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A lirc_serial: use 'setserial /dev/ttySX uart none' So it the problem that receiverserialport and hostserialport are the same. How do i change receiverserialport or can they be the same? |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|