View unanswered posts    View active topics

All times are UTC - 6 hours





Post new topic Reply to topic  [ 5 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
PostPosted: Wed Jan 13, 2010 12:27 am 
Offline
Joined: Tue Feb 14, 2006 12:07 am
Posts: 132
Location: White City OR
Hello,

I am getting an R6 system setup with 4 tunes.
1. HVR-1600
2. PVR-150
3. PVR-150
4. PVR-150

So far its been good, but I cannot get any of my tuners to work above channel 13. Channels 2-13 work, but everything above that are all static.

I tested every tuner indevidually, and they all did the same thing. I am pretty sure all the tuners are not bad. Two of them are brand new, and the other two were working fine in the previous knoppmyth system R5F27.

dmesg | grep ivtv*
Code:
ivtv:  Start initialization, version 1.4.0
ivtv0: Initializing card #0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:02:0b.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ivtv0: Autodetected Hauppauge WinTV PVR-150
cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
ivtv1: Initializing card #1
ivtv1: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:02:0c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ivtv1: Autodetected Hauppauge WinTV PVR-150
cx25840 1-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #1)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: Registered device video1 for encoder MPG (4096 kB)
ivtv1: Registered device video33 for encoder YUV (2048 kB)
ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
ivtv1: Registered device video25 for encoder PCM (320 kB)
ivtv1: Initialized card #1: Hauppauge WinTV PVR-150
ivtv2: Initializing card #2
ivtv2: Autodetected Hauppauge card (cx23416 based)
ivtv 0000:02:0d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
ivtv2: Autodetected Hauppauge WinTV PVR-150
cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #2)
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #2)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #2)
ivtv2: Registered device video2 for encoder MPG (4096 kB)
ivtv2: Registered device video34 for encoder YUV (2048 kB)
ivtv2: Registered device vbi2 for encoder VBI (1024 kB)
ivtv2: Registered device video26 for encoder PCM (320 kB)
ivtv2: Initialized card #2: Hauppauge WinTV PVR-150
ivtv:  End initialization
ivtv 0000:02:0b.0: firmware: requesting v4l-cx2341x-enc.fw
ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
ivtv 0000:02:0c.0: firmware: requesting v4l-cx2341x-enc.fw
ivtv1: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv1: Encoder revision: 0x02060039
ivtv 0000:02:0d.0: firmware: requesting v4l-cx2341x-enc.fw
ivtv2: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv2: Encoder revision: 0x02060039


dmesg | grep dvb*
Code:
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared


Last edited by yaplej on Thu Aug 05, 2010 10:32 pm, edited 1 time in total.


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 13, 2010 12:57 pm 
Offline
Joined: Tue Jul 12, 2005 8:01 am
Posts: 670
Location: Salem, MA
Have you done a channel scan? And do you have other channels setup via your mythfilldatabase source? (schedulesdirect.org in the US)

_________________
LinHES 8.3, 1 BE, 3 FE


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 13, 2010 1:57 pm 
Offline
Joined: Tue Feb 14, 2006 12:07 am
Posts: 132
Location: White City OR
I did do a channel scan, and everything above 13 says "no signal". Thats not true because when its connected to my TV I get a lot of channels above 13.

My SchedulesDirect lineup includes all the channels avaliable in my area.


Top
 Profile  
 
 Post subject:
PostPosted: Wed Jan 13, 2010 2:49 pm 
Offline
Joined: Fri Apr 02, 2004 10:08 am
Posts: 1637
Location: Virginia, USA
Sounds like an incorrect choice for "channel frequency table" in mythtv-setup.

http://www.mythtv.org/wiki/User_Manual: ... eo_sources


Top
 Profile  
 
 Post subject:
PostPosted: Mon Jan 25, 2010 2:20 pm 
Offline
Joined: Tue Feb 14, 2006 12:07 am
Posts: 132
Location: White City OR
ceenvee703 wrote:
Sounds like an incorrect choice for "channel frequency table" in mythtv-setup.


Yup that was it. When I was using KnoppMyth R5F27 the "default" frequency table seems to work if I recall correctly. So I assumed it would also work in R6. See what I get for assuming. Chaging it from "default" to "us-cable" fixed the problem.

Thanks.


Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 


All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu