LinHES Forums http://forums.linhes.org/ |
|
IR Blaster not working (again) http://forums.linhes.org/viewtopic.php?f=21&t=24677 |
Page 1 of 1 |
Author: | Big boy stan [ Mon Aug 28, 2017 7:32 pm ] |
Post subject: | IR Blaster not working (again) |
After the last upgrade, my PVR250 blaster once again stopped working. The remote is working fine but I can not get the blaster to output anything. Doing an irsend gives Code: [mythtv@envy ~]$ irsend SEND_ONCE blaster 3 transmission failed Error running command: Input/output error I made sure I have the correct lircd.conf but still no good. Looking in dmesg I found it complaining about firmware. Code: [ 13.097887] lirc_dev: IR Remote Control driver registered, major 242 [ 13.148598] lirc_zilog: module is from the staging directory, the quality is unknown, you have been warned. [ 13.148610] lirc_zilog: module is from the staging directory, the quality is unknown, you have been warned. [ 13.148860] Zilog/Hauppauge IR driver initializing [ 13.149709] probing IR Tx on ivtv i2c driver #0 (i2c-1) [ 13.209486] i2c i2c-1: Direct firmware load for haup-ir-blaster.bin failed with error -2 [ 13.209489] i2c i2c-1: firmware haup-ir-blaster.bin not available (-2) [ 13.209493] i2c i2c-1: probe of IR Tx on ivtv i2c driver #0 (i2c-1) done. Waiting on IR Rx. [ 13.209495] i2c i2c-1: probe of IR Tx on ivtv i2c driver #0 (i2c-1) done [ 13.209508] probing IR Rx on ivtv i2c driver #0 (i2c-1) [ 13.209669] i2c i2c-1: lirc_dev: driver lirc_zilog registered at minor = 0 [ 13.209671] i2c i2c-1: IR unit on ivtv i2c driver #0 (i2c-1) registered as lirc0 and ready [ 13.209673] i2c i2c-1: probe of IR Rx on ivtv i2c driver #0 (i2c-1) done Anyone see anything in there to tell me why. Thanks for any help. |
Author: | bobmyth [ Tue Aug 29, 2017 9:30 pm ] |
Post subject: | Re: IR Blaster not working (again) |
Maybe this can help: http://forums.linhes.org/viewtopic.php?f=22&t=24081 |
Author: | Big boy stan [ Fri Dec 15, 2017 10:24 am ] |
Post subject: | Re: IR Blaster not working (again) |
I am still not able to get my IRBlaster to send. dmesg reports: Code: dmesg | grep blast [ 10.587456] ivtv0: Reopen i2c bus for IR-blaster support [ 12.958041] i2c i2c-1: Direct firmware load for haup-ir-blaster.bin failed with error -2 [ 12.958047] i2c i2c-1: firmware haup-ir-blaster.bin not available (-2) I tried to load up the Zilog firmware using the advice from the above link but got this: Code: [mythtv@envy ~]$ sudo pacman -S zilog-firmware resolving dependencies... looking for conflicting packages... Package (1) New Version Net Change core/zilog-firmware 1-2 0.30 MiB Total Installed Size: 0.30 MiB :: Proceed with installation? [Y/n] Y (1/1) checking keys in keyring [######################] 100% (1/1) checking package integrity [######################] 100% (1/1) loading package files [######################] 100% (1/1) checking for file conflicts [######################] 100% error: failed to commit transaction (conflicting files) zilog-firmware: /lib exists in filesystem Errors occurred, no packages were upgraded. Any idea why the firmware wont load? |
Author: | brfransen [ Fri Dec 15, 2017 11:44 am ] |
Post subject: | Re: IR Blaster not working (again) |
Problem with the package. Should be fixed now. Code: pacman -Syyy zilog-firmware
|
Page 1 of 1 | All times are UTC - 6 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |