View unanswered posts    View active topics

All times are UTC - 6 hours





Post new topic Reply to topic  [ 2 posts ] 
Print view Previous topic   Next topic  
Author Message
Search for:
PostPosted: Sun Jun 06, 2010 2:23 pm 
Offline
Joined: Thu Mar 16, 2006 10:46 pm
Posts: 17
Installed 6.02 recently. My hauppage pvr-150 grey remote works perfectly, but i'm having trouble getting the IR blaster to do anything. I see this in the lirc logs:
Code:
lircd: accepted new client on /dev/lircd
lircd: error processing command: SEND_ONCE blaster 2
lircd: hardware does not support sending
lircd: removed client

I copied my channel change script from my old r5.5 system. It is basically doing this:
Code:
irsend SEND_ONCE blaster 2

/var/log/messages has:
Code:
Jun  5 16:48:41 mythtv lirc_dev: IR Remote Control driver registered, major 61
Jun  5 16:48:41 mythtv bttv: driver version 0.9.17 loaded
Jun  5 16:48:41 mythtv bttv: using 8 buffers with 2080k (520 pages) each for cap
ture
Jun  5 16:48:41 mythtv ivtv:  Start initialization, version 1.4.0
Jun  5 16:48:41 mythtv ivtv0: Initializing card #0
Jun  5 16:48:41 mythtv ivtv0: Autodetected Hauppauge card (cx23416 based)
Jun  5 16:48:41 mythtv ivtv 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Jun  5 16:48:41 mythtv ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
Jun  5 16:48:41 mythtv tveeprom 0-0050: Hauppauge model 26152, rev C599, serial# 8958264
Jun  5 16:48:41 mythtv tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
Jun  5 16:48:41 mythtv tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
Jun  5 16:48:41 mythtv tveeprom 0-0050: audio processor is CX25843 (idx 37)
Jun  5 16:48:41 mythtv tveeprom 0-0050: decoder processor is CX25843 (idx 30)
Jun  5 16:48:41 mythtv tveeprom 0-0050: has no radio, has IR receiver, has IR transmitter
Jun  5 16:48:41 mythtv ivtv0: Autodetected Hauppauge WinTV PVR-150
Jun  5 16:48:41 mythtv ivtv0: Reopen i2c bus for IR-blaster support
Jun  5 16:48:41 mythtv cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
Jun  5 16:48:41 mythtv tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Jun  5 16:48:41 mythtv wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
Jun  5 16:48:41 mythtv tuner-simple 0-0061: creating new instance
Jun  5 16:48:41 mythtv tuner-simple 0-0061: type set to 50 (TCL 2002N)
Jun  5 16:48:41 mythtv ivtv0: Registered device video0 for encoder MPG (4096 kB)
Jun  5 16:48:41 mythtv ivtv0: Registered device video32 for encoder YUV (2048 kB)
Jun  5 16:48:41 mythtv ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
Jun  5 16:48:41 mythtv ivtv0: Registered device video24 for encoder PCM (320 kB)
Jun  5 16:48:41 mythtv ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
Jun  5 16:48:41 mythtv ivtv:  End initialization
Jun  5 16:48:41 mythtv cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
Jun  5 16:48:41 mythtv lirc_i2c: chip 0x10020 found @ 0x71 (Hauppauge PVR150)
Jun  5 16:48:41 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10



What does the 'Reopen i2c bus for IR-blaster support' message mean?

Any ideas of things I can try?

lsmod|grep lirc

Code:
lirc_imon              18056  1
usbcore               136848  4 lirc_imon,uhci_hcd,ehci_hcd
lirc_i2c               10756  1
lirc_dev               13492  2 lirc_imon,lirc_i2c
i2c_core               22804  38 i2c_viapro,nvidia,wm8775,cx25840,tuner,tea5767,tda8290,tda18271,tda827x,mt20xx,tea5761,ivtv,bttv,v4l2_common,lirc_i2c,cx88_vp3054_i2c,mt352,cx88xx,i2c_algo_bit,tveeprom,tuner_xc2028,s5h1409,xc5000,dvb_pll,s5h1411,or51132,cx24116,nxt200x,isl6421,stb6000,tda9887,tuner_simple,zl10353,cx24123,lgdt330x,stv0299,stv0288,cx22702


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jun 10, 2010 7:52 pm 
Offline
Joined: Thu Mar 16, 2006 10:46 pm
Posts: 17
I figured it out. I needed 'lirc_pvr150' added to the top of my /etc/modules.mythvantage file. I think if I would have gone through the LinHES setup menu for the remote after the initial install, it would have done this for me.


Top
 Profile  
 

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 


All times are UTC - 6 hours




Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group

Theme Created By ceyhansuyu