| LinHES Forums http://forums.linhes.org/ |
|
| Need help getting PVR-150 IR blaster to work http://forums.linhes.org/viewtopic.php?f=23&t=21112 |
Page 1 of 1 |
| Author: | firesnatch [ Sun Jun 06, 2010 2:23 pm ] |
| Post subject: | Need help getting PVR-150 IR blaster to work |
Installed 6.02 recently. My hauppage pvr-150 grey remote works perfectly, but i'm having trouble getting the IR blaster to do anything. I see this in the lirc logs: Code: lircd: accepted new client on /dev/lircd lircd: error processing command: SEND_ONCE blaster 2 lircd: hardware does not support sending lircd: removed client I copied my channel change script from my old r5.5 system. It is basically doing this: Code: irsend SEND_ONCE blaster 2 /var/log/messages has: Code: Jun 5 16:48:41 mythtv lirc_dev: IR Remote Control driver registered, major 61 Jun 5 16:48:41 mythtv bttv: driver version 0.9.17 loaded Jun 5 16:48:41 mythtv bttv: using 8 buffers with 2080k (520 pages) each for cap ture Jun 5 16:48:41 mythtv ivtv: Start initialization, version 1.4.0 Jun 5 16:48:41 mythtv ivtv0: Initializing card #0 Jun 5 16:48:41 mythtv ivtv0: Autodetected Hauppauge card (cx23416 based) Jun 5 16:48:41 mythtv ivtv 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 Jun 5 16:48:41 mythtv ivtv0: Unreasonably low latency timer, setting to 64 (was 32) Jun 5 16:48:41 mythtv tveeprom 0-0050: Hauppauge model 26152, rev C599, serial# 8958264 Jun 5 16:48:41 mythtv tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50) Jun 5 16:48:41 mythtv tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) Jun 5 16:48:41 mythtv tveeprom 0-0050: audio processor is CX25843 (idx 37) Jun 5 16:48:41 mythtv tveeprom 0-0050: decoder processor is CX25843 (idx 30) Jun 5 16:48:41 mythtv tveeprom 0-0050: has no radio, has IR receiver, has IR transmitter Jun 5 16:48:41 mythtv ivtv0: Autodetected Hauppauge WinTV PVR-150 Jun 5 16:48:41 mythtv ivtv0: Reopen i2c bus for IR-blaster support Jun 5 16:48:41 mythtv cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) Jun 5 16:48:41 mythtv tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) Jun 5 16:48:41 mythtv wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) Jun 5 16:48:41 mythtv tuner-simple 0-0061: creating new instance Jun 5 16:48:41 mythtv tuner-simple 0-0061: type set to 50 (TCL 2002N) Jun 5 16:48:41 mythtv ivtv0: Registered device video0 for encoder MPG (4096 kB) Jun 5 16:48:41 mythtv ivtv0: Registered device video32 for encoder YUV (2048 kB) Jun 5 16:48:41 mythtv ivtv0: Registered device vbi0 for encoder VBI (1024 kB) Jun 5 16:48:41 mythtv ivtv0: Registered device video24 for encoder PCM (320 kB) Jun 5 16:48:41 mythtv ivtv0: Initialized card #0: Hauppauge WinTV PVR-150 Jun 5 16:48:41 mythtv ivtv: End initialization Jun 5 16:48:41 mythtv cx88/0: cx2388x v4l2 driver version 0.0.6 loaded Jun 5 16:48:41 mythtv lirc_i2c: chip 0x10020 found @ 0x71 (Hauppauge PVR150) Jun 5 16:48:41 mythtv lirc_dev: lirc_register_plugin: sample_rate: 10 What does the 'Reopen i2c bus for IR-blaster support' message mean? Any ideas of things I can try? lsmod|grep lirc Code: lirc_imon 18056 1
usbcore 136848 4 lirc_imon,uhci_hcd,ehci_hcd lirc_i2c 10756 1 lirc_dev 13492 2 lirc_imon,lirc_i2c i2c_core 22804 38 i2c_viapro,nvidia,wm8775,cx25840,tuner,tea5767,tda8290,tda18271,tda827x,mt20xx,tea5761,ivtv,bttv,v4l2_common,lirc_i2c,cx88_vp3054_i2c,mt352,cx88xx,i2c_algo_bit,tveeprom,tuner_xc2028,s5h1409,xc5000,dvb_pll,s5h1411,or51132,cx24116,nxt200x,isl6421,stb6000,tda9887,tuner_simple,zl10353,cx24123,lgdt330x,stv0299,stv0288,cx22702 |
|
| Author: | firesnatch [ Thu Jun 10, 2010 7:52 pm ] |
| Post subject: | |
I figured it out. I needed 'lirc_pvr150' added to the top of my /etc/modules.mythvantage file. I think if I would have gone through the LinHES setup menu for the remote after the initial install, it would have done this for me. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|