| Author |
Message |
|
j0ly
|
 Posted: Fri Dec 23, 2005 4:44 pm |
|
|
Joined: Sat Feb 05, 2005 3:26 pm
Posts: 121
Location:
Calgary, Alberta - Canada!
|
yup, or what i do is copy the dmesg file to my var/www folder and download it on your windows machine
do this
Quote: cp /var/log/dmesg /var/www go to your windows box and type in Quote: http://your.mythservers.ip.address/dmesg
open with notepad and paste in here!
|
|
| Top |
|
 |
|
Matouka
|
Posted: Fri Dec 23, 2005 4:59 pm |
|
|
Joined: Wed Nov 23, 2005 7:44 am
Posts: 12
|
Yippie, mounted it  here it is:
Code: ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.8 (tagged release) loading
ivtv: Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61]
tveeprom: Hauppauge: model = 26039, rev = C1A5, serial# = 8499387
tveeprom: tuner = <unknown> (idx = 105, type = 4)
tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
tveeprom: audio processor = CX25842 (type = 24)
tveeprom: decoder processor = CX25842 (type = 1d)
ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50]
cx25840: loading /lib/modules/HcwMakoA.ROM
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000010dc0099b71b]
ivtv: i2c attach to card #0 ok [client=cx25840[50], addr=44]
ivtv: i2c attach to card #0 ok [client=wm8775[50], addr=1b]
tda9885/6/7: chip found @ 0x86
ivtv: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv: loading /lib/modules/ivtv-fw-enc.bin
ivtv: Encoder revision: 0x02040011
ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner: type set to 4 (NoTuner) by ivtv i2c driver #0
Vendor: Generic Model: CF Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
Vendor: Model: Rev:
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 0b 00 00 08
sdb: assuming drive cache: write through
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 0b 00 00 08
sdb: assuming drive cache: write through
sdb: sdb1
Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
usb-storage: device scan complete
ivtv: Initialized WinTV PVR 150, card #0
ivtv: ==================== END INIT IVTV ====================
|
|
| Top |
|
|
|
j0ly
|
Posted: Fri Dec 23, 2005 5:00 pm |
|
|
Joined: Sat Feb 05, 2005 3:26 pm
Posts: 121
Location:
Calgary, Alberta - Canada!
|
|
k anything about lirc_pvr150?
|
|
| Top |
|
|
|
Matouka
|
Posted: Fri Dec 23, 2005 5:02 pm |
|
|
Joined: Wed Nov 23, 2005 7:44 am
Posts: 12
|
|
Just did a search for that and it came up empty.. is that bad?
|
|
| Top |
|
|
|
Matouka
|
Posted: Fri Dec 23, 2005 5:03 pm |
|
|
Joined: Wed Nov 23, 2005 7:44 am
Posts: 12
|
|
I can still use my remote and the blaster flashes.. just that the tuner doesn't work.. I'm assuming that lirc is to do with the remote?
|
|
| Top |
|
|
|
j0ly
|
Posted: Fri Dec 23, 2005 5:07 pm |
|
|
Joined: Sat Feb 05, 2005 3:26 pm
Posts: 121
Location:
Calgary, Alberta - Canada!
|
|
are you willing to give me shell acsess? on your computer, i just got ivtv working properly on mine, and the remote as well...
pm me your ip and your root pass (you can change it after)
|
|
| Top |
|
|
|
tjc
|
Posted: Fri Dec 23, 2005 5:43 pm |
|
|
Joined: Thu Mar 25, 2004 11:00 am
Posts: 9551
Location:
Arlington, MA
|
Quote: tveeprom: Hauppauge: model = 26039, rev = C1A5, serial# = 8499387
tveeprom: tuner = <unknown> (idx = 105, type = 4)
Hey this isn't one of those miserable Samsung tuner chips that have been giving people fits on the PVR-500s is it? They show up as type 4 (no tuner found) too. The 150 and 500s tend to share components so it was just a matter of time before these showed up on the 150s...
|
|
| Top |
|
|
|
j0ly
|
Posted: Fri Dec 23, 2005 5:46 pm |
|
|
Joined: Sat Feb 05, 2005 3:26 pm
Posts: 121
Location:
Calgary, Alberta - Canada!
|
|
i have it now working on my machine, the blaster and the remote, im comming up with the fix right away... within the day - ive been in contact with Mark, the guy who wrote the pvr-150 ir drivers ...
|
|
| Top |
|
|
|
j0ly
|
Posted: Sat Dec 24, 2005 1:09 am |
|
|
Joined: Sat Feb 05, 2005 3:26 pm
Posts: 121
Location:
Calgary, Alberta - Canada!
|
|
k guys, give me a couple of days to master the setup, and i swear ill have it working for you... it seems to be working on my r26 version no problem... Tutorial to come...
|
|
| Top |
|
|
|
renfield33
|
Posted: Mon Dec 26, 2005 9:03 pm |
|
|
Joined: Tue Nov 08, 2005 10:51 am
Posts: 13
|
|
i look forward to your solution. the remote is the only thing that keeps me from using the myth box all the time instead of the TiVo.
|
|
| Top |
|
|
|
j0ly
|
Posted: Mon Dec 26, 2005 10:43 pm |
|
|
Joined: Sat Feb 05, 2005 3:26 pm
Posts: 121
Location:
Calgary, Alberta - Canada!
|
|
1 day and we are still working now, only problem im having is with the audio, sounding a little robotic. trying to find a solution, in talks with ivtv devs.
More to come!
|
|
| Top |
|
|
|
spydirweb
|
Posted: Wed Dec 28, 2005 5:40 am |
|
|
Joined: Fri Nov 25, 2005 10:32 pm
Posts: 25
Location:
UNC-C
|
|
out of the box with R5A26 my card's working, except the remote. Everything's fine BUT that. All I use is the remote, I don't need the IR blaster...I just can't get it to work at all. Can you maybe forward me that much of the tutorial?...
_________________ www.netsyndrome.net -- designs.netsyndrome.net -- www.mobileasses.com
|
|
| Top |
|
|
|
JohnNJ
|
Posted: Thu Jan 05, 2006 11:11 pm |
|
|
Joined: Thu Jan 05, 2006 11:05 pm
Posts: 3
|
|
I have the PVR-150 and the IR Receiver works with KnoppMyth R16. I can't get the IR Blaster to work. This and the MythGame module are the only things left.
j0ly can you provide me with some assistance if you have this working.
|
|
| Top |
|
|
|
RobTheGob
|
Posted: Sat Jan 07, 2006 12:24 pm |
|
|
Joined: Tue Oct 25, 2005 7:04 am
Posts: 58
Location:
Victoria, BC
|
|
I wanted to say thanks for this thread. I recently added a second PVR-150 to my Knoppmyth box and was able to successfully get both blasters working with two sat recv'rs.
Thanks!
|
|
| Top |
|
|
|
mihanson
|
Posted: Mon Jan 09, 2006 12:17 pm |
|
|
Joined: Sun Sep 25, 2005 3:50 pm
Posts: 1013
Location:
Los Angeles
|
I had my PVR 150 blaster/remote working just fine under R5A26 until I had to reinstall R5A26. I have changed nothing hardware or software wise. Same box, same old hardware, same version of Knoppmyth. When I reinstalled, everything seemed to go well. This was not an upgrade. It's a clean install. I even had the blaster/remote working until I had to reboot the machine. Upon reboot, I get his message in my syslog:
Code: Jan 8 18:01:12 mythbox kernel: lirc_dev: IR Remote Control driver registered, at major 61
Jan 8 18:01:12 mythbox kernel: lirc_pvr150: ivtv i2c driver #0: no devices found
As you can see below, it was previously working: Code: Jan 8 17:01:54 mythbox kernel: lirc_dev: IR Remote Control driver registered, at major 61
Jan 8 17:01:54 mythbox kernel: lirc_pvr150: chip found with RX and TX
Jan 8 17:01:54 mythbox kernel: ivtv0: i2c attach to card #0 ok [client=Hauppauge PVR150 IR RX, addr=71]
Jan 8 17:01:54 mythbox kernel: ivtv0: i2c attach to card #0 ok [client=Hauppauge PVR150 IR TX, addr=70]
Jan 8 17:01:54 mythbox kernel: lirc_dev: lirc_register_plugin: sample_rate: 0
Jan 8 17:01:54 mythbox kernel: lirc_pvr150: firmware of size 209327 loaded
Jan 8 17:01:54 mythbox kernel: lirc_pvr150: 575 codesets loaded
Jan 8 17:01:54 mythbox kernel: lirc_pvr150: Hauppauge PVR-150 IR blaster: firmware version 1.3.0
So after rebooting a few more times intersperced with banging my head against the wall, I started again, following this guide's instructions. Code: # cd /usr/src/lirc-0.7.2pvr150
# make uninstall
# make clean
# make distclean
# ./configure
select TV card and "h" Hauppague PVR-150 TV Card; save & run configure
# make && make install
# reboot (I also tried not rebooting here)
# modprobe lirc_dev debug=1 && modprobe lirc_pvr150 debug=1
I check the syslog and I find this at the end: Code: Jan 9 09:40:09 mythbox kernel: lirc_dev: IR Remote Control driver registered, at major 61
Jan 9 09:40:09 mythbox kernel: lirc_pvr150: probe 0x70 @ ivtv i2c driver #0: no
Jan 9 09:40:09 mythbox kernel: lirc_pvr150: probe 0x71 @ ivtv i2c driver #0: no
Jan 9 09:40:09 mythbox kernel: lirc_pvr150: ivtv i2c driver #0: no devices found
My PVR-150 is recognized in the IVTV section: Code: Jan 9 09:42:58 mythbox kernel: lirc_dev: IR Remote Control driver registered, at major 61
Jan 9 09:42:58 mythbox kernel: tuner (ivtv): chip found at addr 0xc2 i2c-bus cx88[0]
Jan 9 09:42:58 mythbox kernel: tuner: type set to 52 (Thomson DDT 7610 (ATSC/NTSC)) by cx88[0]
Jan 9 09:42:58 mythbox kernel: ivtv: ==================== START INIT IVTV ====================
Jan 9 09:42:58 mythbox kernel: ivtv: version 0.4.0 (tagged release) loading
Jan 9 09:42:58 mythbox kernel: ivtv: Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
Jan 9 09:42:58 mythbox kernel: ivtv: In case of problems please include the debug info
Jan 9 09:42:58 mythbox kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when
Jan 9 09:42:58 mythbox kernel: ivtv: mailing the ivtv-devel mailinglist.
Jan 9 09:42:58 mythbox kernel: ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
Jan 9 09:42:58 mythbox kernel: PCI: Found IRQ 10 for device 0000:00:08.0
Jan 9 09:42:58 mythbox kernel: PCI: Sharing IRQ 10 with 0000:00:0b.0
Jan 9 09:42:58 mythbox kernel: tveeprom: ivtv version
Jan 9 09:42:58 mythbox kernel: tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 2985395
Jan 9 09:42:58 mythbox kernel: tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
Jan 9 09:42:58 mythbox kernel: tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
Jan 9 09:42:58 mythbox kernel: tveeprom: audio processor = CX25841 (type = 23)
Jan 9 09:42:58 mythbox kernel: tveeprom: decoder processor = CX25841 (type = 1c)
Jan 9 09:42:58 mythbox kernel: ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
Jan 9 09:42:58 mythbox kernel: tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Jan 9 09:42:58 mythbox kernel: ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
Jan 9 09:42:58 mythbox kernel: cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
Jan 9 09:42:59 mythbox kernel: cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
Jan 9 09:42:59 mythbox kernel: ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
Jan 9 09:43:00 mythbox kernel: wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
Jan 9 09:43:00 mythbox kernel: ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
Jan 9 09:43:00 mythbox kernel: tda9885/6/7: (ivtv) chip found @ 0x86
Jan 9 09:43:00 mythbox kernel: ivtv0: loading /lib/modules/ivtv-fw-enc.bin
Jan 9 09:43:00 mythbox kernel: ivtv0: Encoder revision: 0x02040011
Jan 9 09:43:00 mythbox kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
Jan 9 09:43:00 mythbox kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
Jan 9 09:43:00 mythbox kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
Jan 9 09:43:00 mythbox kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
Jan 9 09:43:00 mythbox kernel: tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
Jan 9 09:43:01 mythbox kernel: ivtv0: Initialized WinTV PVR 150, card #0
Jan 9 09:43:01 mythbox kernel: ivtv: ==================== END INIT IVTV ====================
Jan 9 09:43:01 mythbox kernel: lirc_pvr150: ivtv i2c driver #0: no devices found
Jan 9 09:43:01 mythbox lircd-0.7.2pvr150[2309]: lircd(any) ready
Can anyone be my hero today? _________________ Mike
My Hardware Profile
|
|
| Top |
|
|
View unanswered posts
View active topics
KnoppMyth 
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register