I replaced the nv driver with the nvidia one. All works well now.


Hi,

I can't seem to figure out how to sync my audio and video on my PVR-250 based system. I seem to be almost 2 seconds out of sync (audio before video).

Also, my audio comes out warbled (I don't know how else to describe it.

I initially had no audio, and recompiled ivtv.

I searched the list, but couldn't find anything. Any ideas where to look so I can fix this?

Thanks,

Gerald


latest KnopMyth
PVR-250
Athlon 2400


Linux video capture interface: v1.00
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-algo-bit.o: i2c bit algorithm module
i2c-core.o: driver i2c TV tuner driver registered.
i2c-core.o: driver saa7115 registered.
i2c-core.o: driver i2c msp3400 driver registered.
ivtv: version 0.1.9 (release) loading
ivtv: SGarray_size = 340, DSGarray_size = 16
ivtv: Found an iTVC16 based chip
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
i2c-core.o: client [(tuner unset)] registered to adapter [ivtv i2c driver #0](pos. 0).
tuner: type set to 39 (LG NTSC (newer TAPC series)) by insmod option
tuner: The type=<n> insmod option will go away soon.
tuner: Please use the tuner=<n> option provided by
tuner: tv aard core driver (bttv, saa7134, ...) instead.
saa7114.c: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7114.c: detecting saa7114 client on address 0x42
saa7115.c: writing init values
status: (1E) 0x8d, (1F) 0xb1
i2c-core.o: client [saa7115[0]] registered to adapter [ivtv i2c driver #0](pos.
1).
msp34xx: init: chip=MSP3448W-A2, has NICAM support
msp3410: daemon started
i2c-core.o: client [MSP3448W-A2] registered to adapter [ivtv i2c driver #0](pos. 2).
i2c-core.o: adapter ivtv i2c driver #0 registered as adapter 0.
ivtv: Encoder revision: 0x02040011
ivtv: Registered v4l2 device, minor 0
ivtv: Registered v4l2 device, minor 32
ivtv: Registered v4l2 device, minor 224
ivtv: loaded
lirc_dev: IR Remote Control driver registered, at major 61
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
i2c-core.o: driver i2c ir driver registered.
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
i2c-core.o: client [Hauppauge IR] registered to adapter [ivtv i2c driver #0](pos. 3).
lirc_dev: lirc_register_plugin:sample_rate: 10
saa7115[0]: decoder set norm NTSC
saa7115[0] set audio: 0x02
saa7115[0]: decoder set input (0)
saa7115[0]: now setting Composite input
saa7115[0]: decoder set size
Setting full NTSC width
Setting full NTSC height
apm: BIOS not found.
saa7115[0]: decoder set input (4)
saa7115[0]: now setting Composite input
saa7115[0]: decoder set norm NTSC
saa7115[0] set audio: 0x02
saa7115[0]: decoder set picture bright=128 contrast=63 saturation=64 hue=0
saa7115[0]: decoder set picture bright=128 contrast=63 saturation=63 hue=0
saa7115[0]: decoder set picture bright=127 contrast=63 saturation=63 hue=0

etc...