| Author |
Message |
|
IceburgIV
|
 Posted: Wed Jun 14, 2006 7:40 am |
|
|
Joined: Sun Mar 26, 2006 3:42 pm
Posts: 39
|
I have a hauppauge 250, a seriel IR blaster. Comcast Digital cable:
Code: # /etc/irblaster/hardware.conf
#
# Author: Greg Frost
# The COM Port used by the IRBlaster. Set it to "COM1" "COM2" or "".
IRBLASTER_SERIAL_PORT="COM2"
# Set this to the lirc device that will be used by lirc_serial. In my case
# it is /dev/lirc. I have a USB remote, so my remote does not use the
# /dev/lirc device, so it is used by lirc_serial for my ir blaster. If you
# have a remote that uses /dev/lirc, the blaster may user /dev/lirc1. Not
# sure.
IRBLASTER_DEVICE="/dev/lirc1"
Code: nd: General Instrument
# model no. of remote control: dct2244/1161/abcdef
#
begin remote
name Cable
flags RAW_CODES
eps 30
aeps 100
ptrail 0
repeat 0 0
frequency 38000
begin raw_codes
name 1
9200 4600 500 4600 500 2275
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 4600 500 4600
500 4600 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 2
9200 4600 500 2300 500 4600
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 4600
500 4600 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 3
9200 4600 500 4600 500 4600
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 4600 500 2300
500 4600 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 4
9200 4600 500 2300 500 2300
500 4600 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 4600 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 5
9200 4600 500 4600 500 2300
500 4600 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 4600 500 4600
500 2300 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 6
9200 4600 500 2300 500 4600
500 4600 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 4600
500 2300 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 7
9200 4600 500 4600 500 4600
500 4600 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 4600 500 2300
500 2300 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 8
9200 4600 500 2300 500 2300
500 2300 500 4600 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 4600 500 33900
9200 2400 800 94000 9400 2300
800 94000 9400 2300
800
name 9
9200 4600 500 4600 500 2300
500 2300 500 4600 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 4600 500 4600
500 4600 500 2300 500 33900
9200 2400 500 94000 9400 2300
800 94000 9400 2300
800
name 0
9200 4600 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 2300
500 2300 500 2300 500 33900
9200 2400 500 94000 9400 2300
800 94000 9400 2300
800
end raw_codes
end remote
and my script: Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=Cable
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblaster SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
Worked almost flawless in R5B7 but not working so well on R5C7 but I am looking into it. IN R5B7 all I had to do was: Code: update-rc.d -f lirc remove
update-rc.d lirc defaults 20
Thanks for all your hard work Greg and the rest of the team!
|
|
| Top |
|
 |
|
timmayk
|
Posted: Wed Jun 14, 2006 11:54 am |
|
|
Joined: Sat Mar 18, 2006 1:18 pm
Posts: 45
|
I have a hauppauge 350 working with a dish network receiver 311. Thanks all who have helped.
irblasterd.conf in /etc/irblaster
Code: #
# this config file was automatically generated
# using WinLIRC 0.6.5 (LIRC 0.6.1pre3) on Tue Apr 04 06:16:24 2006
#
# contributed by
#
# brand: 301
# model:
# supported devices:
#
begin remote
name 301
bits 16
flags SPACE_ENC
eps 30
aeps 100
header 400 6100
one 400 1700
zero 400 2800
ptrail 400
gap 6200
min_repeat 4
toggle_bit 0
frequency 56000
begin codes
info 0x0000000000000000
power 0x0000000000000800
play 0x0000000000000C10
1 0x0000000000001000
2 0x0000000000001400
3 0x0000000000001800
frwd 0x0000000000001C10
4 0x0000000000002000
5 0x0000000000002400
6 0x0000000000002800
menu 0x0000000000002C00
7 0x0000000000003000
8 0x0000000000003400
9 0x0000000000003800
ffwd 0x0000000000003C10
select 0x0000000000004000
0 0x0000000000004400
cancel 0x0000000000004800
guide 0x0000000000005000
mute 0x0000000000005401
view 0x0000000000005800
tv_video 0x0000000000005C00
right 0x0000000000006000
vol+ 0x0000000000006401
up 0x0000000000006800
recall 0x0000000000006C00
left 0x0000000000007000
vol- 0x0000000000007401
down 0x0000000000007800
rec 0x0000000000007C00
pause 0x0000000000008000
stop 0x0000000000008400
sys_info 0x0000000000009000
*/ptv_list 0x0000000000009400
#/search 0x0000000000009800
sat 0x000000000000A400
tv 0x000000000000A801
rew 0x000000000000C410
fwd 0x000000000000C810
skip_back 0x000000000000D810
skip_fwd 0x000000000000DC10
end codes
end remote
and here is my channel_change.sh located in /etc/irblaster Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=301
$(grep ^[[:space:]]*name[[:space:]] /etc/irblaster/irblasterd.conf |
awk '{ print $2 }')
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
_________________
R5D1, PVR350, ASUS A7N8X-E Deluxe, AMD 2200+, SB Live.
|
|
| Top |
|
|
|
XateEsix
|
Posted: Fri Jun 16, 2006 12:49 pm |
|
|
Joined: Sat Mar 25, 2006 10:17 am
Posts: 4
|
|
Thank you everyone for your help in making knoppmyth the best pvr system anywhere!
I use this remote config to run my Cox Cable Sientific Atlantic SA3250 cable box's
#
# this config file was automatically generated
# using lirc-0.6.6(sir) on Wed Mar 24 22:28:59 2004
#
# Modified by Stephane Lavergne <stephane|iMars.com>:
# Base frequency is 56kHz, irrecord was otherwise right on.
#
# contributed by
#
# brand: Scientific Atlanta
# model no. of remote control: AT8400
# devices being controlled by this remote: Explorer 8000
#
begin remote
name SAE3250
bits 22
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100
header 3397 3372
one 827 2557
zero 827 855
ptrail 827
gap 101386
toggle_bit 0
frequency 56000
begin codes
Power 0x000000000037C107
guide 0x000000000036C127
menu 0x000000000036F920
info 0x000000000036213B
up 0x000000000036812F
down 0x000000000037A10B
select 0x0000000000366133
left 0x000000000037810F
right 0x0000000000364137
page+ 0x000000000036D924
page- 0x000000000037D904
exit 0x0000000000366932
settings 0x0000000000373918
A 0x000000000037E902
B 0x000000000036193C
C 0x000000000037191C
vol+ 0x000000000036093E
vol- 0x000000000037091E
ch+ 0x0000000000377111
ch- 0x000000000036F121
mute 0x000000000036892E
fav 0x000000000037F101
last 0x000000000036E123
rew8sec 0x000000000037C906
list 0x000000000036C926
live 0x000000000036B129
rew 0x000000000037291A
ffw 0x000000000036293A
play 0x000000000037990C
stop 0x0000000000365934
pause 0x0000000000374117
record 0x0000000000375914
1 0x000000000036113D
2 0x000000000037111D
3 0x000000000036912D
4 0x000000000037910D
5 0x0000000000365135
6 0x0000000000375115
7 0x000000000036D125
8 0x000000000037D105
9 0x0000000000363139
asterisk 0x000000000037E103
0 0x0000000000373119
pound 0x000000000036B928
pip_power 0x000000000037B908
pip_swap 0x0000000000367930
pip_move 0x0000000000377910
pip_ch+ 0x000000000036E922
pip_ch- 0x000000000037F900
video_source 0x0000000000376113
end codes
end remote
|
|
| Top |
|
|
|
BluesBrian
|
Posted: Fri Sep 15, 2006 12:00 am |
|
|
Joined: Fri Jul 29, 2005 1:22 am
Posts: 232
Location:
SF East Bay, CA
|
IceburgIV wrote: I have a hauppauge 250, a seriel IR blaster. Comcast Digital cable: and my script: Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=Cable
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblaster SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
Worked almost flawless in R5B7 but not working so well on R5C7 but I am looking into it. IN R5B7 all I had to do was: Code: update-rc.d -f lirc remove
update-rc.d lirc defaults 20
Thanks for all your hard work Greg and the rest of the team! That just about works for me.. except that my DTC2244 prefers either a three digit code or shorter digit count followed by the "enter" key.. or the channel change fails. Results: works great for channels 100 and above. fails for channels <100.
Any Suggestions on how to add leading zeros or a trailing "enter" key? (I'm on R5C7) _________________ // Brian - Hardware:
ASUS P5P800 - P4 3Ghz, 500 GB PATA HD
ASUS P5K-V - P4 Core2 Duo, 500 GB SATA HD
Hauppauge PVR-350, IR Blaster, Comcast Digital Cable
http://tech.groups.yahoo.com/group/KnoppMyth/
KnoppMyth R5F27 >> R5.5
|
|
| Top |
|
|
|
Greg Frost
|
Posted: Fri Sep 15, 2006 1:11 am |
|
|
Joined: Mon May 10, 2004 8:08 pm
Posts: 1891
Location:
Adelaide, Australia
|
BluesBrian wrote: Any Suggestions on how to add leading zeros or a trailing "enter" key? (I'm on R5C7)
Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=Cable
for digit in $(echo $1 | sed -e 's/./& /g'); do
/usr/bin/irsend --device=/dev/irblaster SEND_ONCE $REMOTE_NAME $digit
sleep 0.7
done
/usr/bin/irsend --device=/dev/irblaster SEND_ONCE $REMOTE_NAME Enter
Replace "Enter" on the last line with whatever the name of your enter key is.
|
|
| Top |
|
|
|
BluesBrian
|
Posted: Fri Sep 15, 2006 8:30 am |
|
|
Joined: Fri Jul 29, 2005 1:22 am
Posts: 232
Location:
SF East Bay, CA
|
Greg Frost wrote: Replace "Enter" on the last line with whatever the name of your enter key is.
Thanks Greg!
oops! I'm using the irblasterd.conf file for my dtc2244 suggested by IceburgIV above .. There is no "enter" key! Yikes!
Is there a simple procedure to create this key? _________________ // Brian - Hardware:
ASUS P5P800 - P4 3Ghz, 500 GB PATA HD
ASUS P5K-V - P4 Core2 Duo, 500 GB SATA HD
Hauppauge PVR-350, IR Blaster, Comcast Digital Cable
http://tech.groups.yahoo.com/group/KnoppMyth/
KnoppMyth R5F27 >> R5.5
|
|
| Top |
|
|
|
Greg Frost
|
Posted: Fri Sep 15, 2006 4:31 pm |
|
|
Joined: Mon May 10, 2004 8:08 pm
Posts: 1891
Location:
Adelaide, Australia
|
|
is there an ok key? if not, try looking for another lirc configuration file.
|
|
| Top |
|
|
|
BluesBrian
|
Posted: Sun Sep 17, 2006 1:26 pm |
|
|
Joined: Fri Jul 29, 2005 1:22 am
Posts: 232
Location:
SF East Bay, CA
|
Greg Frost wrote: is there an ok key? if not, try looking for another lirc configuration file.
Thanks again Greg!
At this point, I really don't understand the difference between the code structures Code: begin codes and Code: begin raw_codes .. they are rather different! (mine comes in the "raw_codes" form, and others that I look at are in the "codes" form). Here's my "Plan B" approach.. add leading zeros to the channel change script! Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=DCT2244
if [ $1 -lt 10 ] ; then
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME 0
sleep 0.5
fi
if [ $1 -lt 100 ] ; then
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME 0
sleep 0.5
fi
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
and it works great! (I'm on KnoppMyth R5C7.) _________________ // Brian - Hardware:
ASUS P5P800 - P4 3Ghz, 500 GB PATA HD
ASUS P5K-V - P4 Core2 Duo, 500 GB SATA HD
Hauppauge PVR-350, IR Blaster, Comcast Digital Cable
http://tech.groups.yahoo.com/group/KnoppMyth/
KnoppMyth R5F27 >> R5.5
|
|
| Top |
|
|
|
douw
|
Posted: Tue Oct 10, 2006 5:03 am |
|
|
Joined: Wed May 31, 2006 6:54 am
Posts: 52
Location:
Pretoria, South Africa
|
I just got my Multichoice decoder (settop box) working. Here folows my details:
Knoppmyth R5D1 upgraded to MtyhTv 0.20
A home built irblaster from http://iguanaworks.net/ir/
A DSD910 multichoice satellite decoder
A universal remote from One-For-All; the DSD codes are factory programmed, the VCR codes I just chose one that had functions programmed on all the buttons and created a conf with irrecord.
My irblasterd.conf:
Code: # this config file was adapted from the origional on www.lirc.org/remotes
# using trail and error
#
# contributed Douw Steyn
#
# brand: Multichoice
# model: DSD910
# supported devices: Digital Satellite Decoder (DSTV Decoder)
#
# Multichoice is a South African Satellite TV company offering their
# own branded decoders.
begin remote
name DSD910
bits 13
flags RC5
eps 30
aeps 100
one 902 840
zero 972 840
plead 992
gap 113485
toggle_bit 2
begin codes
power 0x000000000000160C
red 0x000000000000162C
green 0x000000000000162B
yellow 0x000000000000162A
blue 0x000000000000162E
1 0x0000000000001601
2 0x0000000000001602
3 0x0000000000001603
4 0x0000000000001604
5 0x0000000000001605
6 0x0000000000001606
7 0x0000000000001607
8 0x0000000000001608
9 0x0000000000001609
0 0x0000000000001600
radio 0x0000000000001625
tv 0x000000000000162F
mute 0x000000000000160D
teletext 0x0000000000001624
information 0x000000000000162D
up 0x0000000000001612
left 0x000000000000161D
ok 0x0000000000001622
right 0x000000000000161E
down 0x0000000000001613
menu 0x000000000000161C
exit 0x0000000000001631
tvguide 0x0000000000001635
progup 0x0000000000001620
progdn 0x0000000000001621
volup 0x0000000000001610
voldn 0x0000000000001611
end codes
end remote
#
# this config file was automatically generated
# using WinLIRC 0.6.5 (LIRC 0.6.1pre3) on Sun Aug 13 15:51:10 2006
#
# contributed by
#
# brand: VCR
# model:
# supported devices:
#
begin remote
name VCR
bits 16
flags SPACE_ENC
eps 25
aeps 100
header 9026 4439
one 573 533
zero 573 1655
ptrail 573
pre_data_bits 16
pre_data 0xFED9
gap 44827
toggle_bit 0
begin codes
menu 0x000000000000CF30
power 0x0000000000006D92
1 0x0000000000007F80
2 0x000000000000BF40
3 0x0000000000003FC0
4 0x000000000000DF20
5 0x0000000000005FA0
6 0x0000000000009F60
7 0x0000000000001FE0
8 0x000000000000EF10
9 0x0000000000006F90
0 0x000000000000FF00
av 0x0000000000008D72
ch+ 0x000000000000AF50
exit 0x000000000000AD52
ch- 0x0000000000002FD0
up 0x0000000000007D82
left 0x0000000000007788
right 0x000000000000F708
down 0x000000000000BD42
ok 0x0000000000005DA2
vol+ 0x0000000000008F70
mute 0x0000000000004FB0
vol- 0x0000000000000FF0
rew 0x0000000000006798
play 0x0000000000009768
pause 0x000000000000A758
ff 0x000000000000E718
sp/lp 0x0000000000008778
stop 0x00000000000017E8
rec 0x00000000000057A8
auto 0x000000000000E51A
guide 0x000000000000CD32
time 0x000000000000CF30
subtitle 0x00000000000027D8
i 0x000000000000D728
end codes
end remote My channel_change.sh: Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=DSD910
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
sleep 1
/usr/bin/irsend --device=/dev/irblasterd SEND_START $REMOTE_NAME volup
sleep 1.5
/usr/bin/irsend --device=/dev/irblasterd SEND_STOP $REMOTE_NAME volup
I had to remove lirc from init.d and make a symlink from /dev/lircd to /dev/irblasterd to get the receiver to work in the menus, I might have broken that myself to begin with so I am not sure wheather that is relevant to other people.
Last edited by douw on Fri Apr 09, 2010 12:51 am, edited 2 times in total.
|
|
| Top |
|
|
|
rdbeer
|
Posted: Sat Dec 30, 2006 12:25 am |
|
|
Joined: Wed Dec 15, 2004 2:44 pm
Posts: 12
|
I'm not an expert by any means, but here's how I got my stuff working on R5E50:
* home built IR serial port transmitter/receiver ( http://iguanaworks.net/ir/serial/)
* Dish Network 322 dual satellite receiver
* Scientific Atlanta E2050ER1 remote (from my old Scientific Atlanta Explorer 2100)
I am using only the lirc configuration, irblaster is _not_ configured. So assuming no previous lirc/irblaster configuration exists,
1. run lirc-reconfig.sh, choose the only serial remote listed (rca-6n1)
2. do not run irblaster.sh
3. substitue these files:
/etc/lirc/lircd.conf:
(lircd.conf contains codes for both the SA remote and the Dish box. The Dish box has two remotes. substitute
Code: post_data 0x000 to emulate remote 1, or Code: post_data 0x200 to emulate remote 2.) Code: begin remote
name SAE8000
bits 22
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100
header 3397 3372
one 827 2557
zero 827 855
ptrail 827
gap 101386
toggle_bit 0
frequency 56000
begin codes
power 0x000000000037C107
guide 0x000000000036C127
menu 0x000000000036F920
info 0x000000000036213B
select_up 0x000000000036812F
select_down 0x000000000037A10B
select 0x0000000000366133
select_left 0x000000000037810F
select_right 0x0000000000364137
select_page+ 0x000000000036D924
select_page- 0x000000000037D904
exit 0x0000000000366932
settings 0x0000000000373918
A 0x000000000037E902
B 0x000000000036193C
C 0x000000000037191C
vol+ 0x000000000036093E
vol- 0x000000000037091E
ch+ 0x0000000000377111
ch- 0x000000000036F121
mute 0x000000000036892E
fav 0x000000000037F101
last 0x000000000036E123
rew8secs 0x000000000037C906
list 0x000000000036C926
live 0x000000000036B129
rew 0x000000000037291A
ff 0x000000000036293A
play 0x000000000037990C
stop 0x0000000000365934
pause 0x0000000000374117
rec 0x0000000000375914
1 0x000000000036113D
2 0x000000000037111D
3 0x000000000036912D
4 0x000000000037910D
5 0x0000000000365135
6 0x0000000000375115
7 0x000000000036D125
8 0x000000000037D105
9 0x0000000000363139
asterisk 0x000000000037E103
0 0x0000000000373119
pound 0x000000000036B928
pip_power 0x000000000037B908
pip_swap 0x0000000000367930
pip_move 0x0000000000377910
pip_ch+ 0x000000000036E922
pip_ch- 0x000000000037F900
video_source 0x0000000000376113
end codes
end remote
begin remote
name DishNetwork_322
flags SPACE_ENC|NO_HEAD_REP
eps 30
aeps 100
frequency 56000
# duty_cycle 32
one 440 1645
zero 440 2780
header 525 6045
ptrail 450
gap 6115
min_repeat 6
bits 6
post_data_bits 10
# unit code selection (1-16)
# 1=0x000 2=0x200 3=0x100 4=0x300
# 5=0x080 6=0x280 7=0x180 8=0x380
# 9=0x040 10=0x240 11=0x140 12=0x340
# 13=0x0C0 14=0x2C0 15=0x1C0 16=0x3C0
post_data 0x000
begin codes
info 0
power_on 1
power 2
1 4
2 5
3 6
4 8
5 9
6 10
menu 11
7 12
8 13
9 14
select 16
0 17
cancel 18
guide 20
view 22
tv_vcr 23
right 24
up 26
recall 27
left 28
down 30
record 31
pause 32
stop 33
sys_info 36
asterisk 37
pound 38
power_off 39
sat 41
dish_home 52
sys_info2 54
dish_home2 56
end codes
end remote /etc/lirc/hardware.conf: Code: LIRCD_ARGS=""
#Don't start lircmd even if there seems to be a good config file
START_LIRCMD=false
#Try to load appropriate kernel modules
LOAD_MODULES=true
# Run "lircd --driver=help" for a list of supported drivers.
DRIVER="default"
# If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0
# udev uses /dev/lirc0 will be automatically used instead
DEVICE="/dev/lirc0"
MODULES="lirc_dev lirc_serial" /etc/irblaster/channel_change.sh: Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME="DishNetwork_322"
for digit in $(echo $1 | sed -e 's/./& /g'); do
/usr/bin/irsend SEND_ONCE $REMOTE_NAME $digit
sleep 0.2
done
/usr/bin/irsend SEND_ONCE $REMOTE_NAME select
sleep 0.2
/usr/bin/irsend SEND_ONCE $REMOTE_NAME cancel /home/mythtv/.mythtv/lircrc: Code: # MythTV - standard keys (as suggested by keys.txt)
begin
prog = mythtv
button = 0
config = 0
end
begin
prog = mythtv
button = 1
config = 1
end
begin
prog = mythtv
button = 2
config = 2
end
begin
prog = mythtv
button = 3
config = 3
end
begin
prog = mythtv
button = 4
config = 4
end
begin
prog = mythtv
button = 5
config = 5
end
begin
prog = mythtv
button = 6
config = 6
end
begin
prog = mythtv
button = 7
config = 7
end
begin
prog = mythtv
button = 8
config = 8
end
begin
prog = mythtv
button = 9
config = 9
end
begin
prog = mythtv
button = select_left
config = Left
end
begin
prog = mythtv
button = select_right
config = Right
end
begin
prog = mythtv
button = select_up
config = Up
end
begin
prog = mythtv
button = select_down
config = Down
end
begin
prog = mythtv
button = select
config = Space
end
begin
prog = mythtv
button = exit
config = Esc
end
begin
prog = mythtv
button = guide
config = M
end
begin
prog = mythtv
button = pause
config = P
end
begin
prog = mythtv
button = info
config = I
end
# MythTV - additional keys
# delete
begin
prog = mythtv
button = C
config = D
end
begin
prog = mythtv
button = vol-
repeat = 3
config = F10
end
begin
prog = mythtv
button = vol+
repeat = 3
config = F11
end
begin
prog = mythtv
button = mute
config = F9
end
begin
prog = mythtv
button = play
config = P
end
begin
prog = mythtv
button = rec
config = R
end
# backward commercial skip
begin
prog = mythtv
button = rew
config = Q
end
# forward commercial skip
begin
prog = mythtv
button = ff
config = Z
end
# channel history
begin
prog = mythtv
button = last
config = H
end
# go to next favorite
begin
prog = mythtv
button = fav
config = /
end
# mark favorite
begin
prog = mythtv
button = B
config = ?
end
# cycle through zoom modes
begin
prog = mythtv
button = A
config = W
end
### MPlayer ###
begin
prog = mplayer
button = exit
config = quit
end
begin
prog = mplayer
button = guide
config = osd
end
begin
prog = mplayer
button = select_left
config = seek -10
end
begin
prog = mplayer
button = select_right
config = seek +10
end
begin
prog = mplayer
button = rew
config = seek -60
end
begin
prog = mplayer
button = ff
config = seek +60
end
begin
prog = mplayer
button = pause
config = pause
end
begin
prog = mplayer
button = play
config = pause
end
begin
prog = mplayer
button = vol+
config = volume +1
repeat = 3
end
begin
prog = mplayer
button = vol-
config = volume -1
repeat = 3
end
begin
prog=mplayer
button=mute
config=mute
end
begin
prog=mplayer
button = select_page-
config = panscan -0.1
end
begin
prog=mplayer
button = select_page+
config = panscan +0.1
end
### XINE ###
begin
prog = xine
button = play
config = Play
end
begin
prog = xine
button = stop
config = Stop
end
begin
prog = xine
button = exit
config = Quit
end
begin
prog = xine
button = pause
config = Pause
end
begin
prog = xine
button = select_up
config = EventUp
end
begin
prog = xine
button = select_down
config = EventDown
end
begin
prog = xine
button = select_left
config = EventLeft
end
begin
prog = xine
button = select_right
config = EventRight
end
begin
prog = xine
button = select
config = EventSelect
end
begin
prog = xine
button = guide
config = Menu
end
#vol down
begin
prog = xine
button = vol-
repeat = 3
config = Volume-
end
#vol up
begin
prog = xine
button = vol+
repeat = 3
config = Volume+
end
begin
prog = xine
button = ff
config = SeekRelative+10
end
begin
prog = xine
button = rew
config = SeekRelative-10
end
#ch up
begin
prog = xine
button = select_page+
config = SeekRelative+60
end
#ch down
begin
prog = xine
button = select_page-
repeat = 1
config = SeekRelative-60
end
#sleep
begin
prog = xine
button = fav
repeat = 1
config = ZoomIn
end
#display
begin
prog = xine
button = last
repeat = 1
config = ZoomOut
end
#skip chapter forward
begin
prog = xine
button = ch+
repeat = 1
config = EventNext
end
#skip chapter backward
begin
prog = xine
button = ch-
repeat = 1
config = EventPrior
end
### lircnav ###
begin
prog = lircnav
button = select_page-
config = page_down
end
begin
prog = lircnav
button = select_page+
config = page_up
end
begin
prog = lircnav
button = select_up
config = up
end
begin
prog = lircnav
button = select_down
config = down
end
begin
prog = lircnav
button = select
config = select
end
begin
prog = lircnav
button = exit
config = quit
end I also use the stb_updater.pl script from http://dyn.yoderhome.com:8080/stb_updater.pl, modified to use my remote commands. I added (or was it added automatically? i'm not sure) this line to /etc/init.d/bootmisc.sh: Code: setserial /dev/ttyS0 uart none
|
|
| Top |
|
|
|
aelinuxguy
|
Posted: Sun Feb 11, 2007 10:40 am |
|
|
Joined: Sat Feb 21, 2004 11:54 am
Posts: 48
|
The IR Blaster setup works out of the box for me if I pick a compatible receiver, but it may save others a bit of research if an entry was added to the list. In the Wadsworth, Ohio area Time Warner Cable uses the Pioneer BD-V1100. This unit works if you pick the Explorer 8000 from the irblaster setup script. The only other thing I had to do to get it working from a stock install of R5E20 was copy /etc/irblaster/channel_change.sh from my previous installation and ensure it was specified as the change channel script:
Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=\
$(grep ^[[:space:]]*name[[:space:]] /etc/irblaster/irblasterd.conf |
awk '{ print $2 }')
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
|
|
| Top |
|
|
|
Das Hammer
|
Posted: Thu Feb 22, 2007 10:20 am |
|
|
Joined: Sun Apr 30, 2006 9:06 pm
Posts: 59
Location:
Das Hoosier State
|
Please include the Motorola DSR-922 satellite receiver in the config.
I have found the LIRC config for this device here:
http://www.a9k.net/lirc/4dtv.conf
_________________
Proud member of the Loyal Brotherhood of Snipe Hunters - Local 414
|
|
| Top |
|
|
|
chris_s
|
Posted: Tue Feb 27, 2007 10:05 pm |
|
|
Joined: Wed Feb 14, 2007 10:37 am
Posts: 38
|
I have a motorola RG2400, which uses a remote called the SRC-200A
Here is a link to the config for LIRC
http://lirc.sourceforge.net/remotes/motorola/SRC-200A
_________________
noob. please forgive my ignorance.
running: r5e50, pvr350, p4 1.7ghz 512mb ram, nvidia fx5200, 27" flat tube tv
|
|
| Top |
|
|
|
jmairs
|
Posted: Tue Apr 10, 2007 6:34 pm |
|
|
|
Hi,
I have an RCA 7th generation DirecTV receiver (DRD4##RH)
Here's the /etc/irblasterd.conf file
Code: #
# This is the configuration file for the RCA DirecTV
# Universal remote for 6th (DRD4##RG) and 7th (DRD4##RH)
# generation DirecTV cable boxes. This includes systems
# marked as "RF" which also have an IR receiver.
#
# This file was created with irrecord (0.6.6) and by hand
# on April 24, 2003 by Bryan Jacobs <bryan_jj@hotmail.com>.
# It has since been tested with 7th genration boxes. Please
# contact me if this file does not work as specified for
# for your specific box.
#
# This only contains code for "SAT/DIRECTTV" mode.
# On some remotes the "OK" button is labeled "SELECT"
#
begin remote
name RCA_DSS_RG_RH
bits 24
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100
header 4000 4000
one 500 2000
zero 500 1000
ptrail 500
gap 64000
toggle_bit 0
begin codes
ANTENNA 0x00000000007058FA
CLEAR 0x00000000007068F9
MENU 0x00000000007088F7
GUIDE 0x000000000071A8E5
GO_BACK 0x00000000007278D8
ON/OFF 0x000000000072A8D5
CH- 0x000000000072C8D3
CH+ 0x000000000072D8D2
0 0x00000000007308CF
1 0x00000000007318CE
2 0x00000000007328CD
3 0x00000000007338CC
4 0x00000000007348CB
5 0x00000000007358CA
6 0x00000000007368C9
7 0x00000000007378C8
8 0x00000000007388C7
9 0x00000000007398C6
SAT 0x000000000073A8C5
INFO 0x000000000073C8C3
SKIP 0x00000000007538AC
LEFT_ARROW 0x00000000007568A9
RIGHT_ARROW 0x00000000007578A8
DOWN_ARROW 0x00000000007588A7
UP_ARROW 0x00000000007598A6
WHO 0x000000000076189E
FETCH 0x000000000079386C
OK 0x00000000007F480B
VOL- 0x0000000000F2E0D1
VOL+ 0x0000000000F2F0D0
MUTE 0x0000000000F3F0C0
end codes
end remote
Here's the channel_change.sh script Code: #!/bin/bash
echo "changing to $1"
REMOTE_NAME=RCA_DSS_RG_RH
for digit in $(echo $1 | sed -e 's/./& /g'); do
sleep 0.2
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME $digit
sleep 0.5
done
|
|
| Top |
|
|
|
vabiro
|
Posted: Wed May 21, 2008 1:58 pm |
|
|
Joined: Sun Feb 26, 2006 11:34 pm
Posts: 83
Location:
Toronto, ON, Canada
|
Hi,
Here are the codes 1 through 4 for the expressVu 3100/4100/dish 301
I am using this irblaster.conf to control 4 receivers that are feeding 2 Hauppauge PVR-500 cards.
Code: begin remote
name code1
bits 8
flags SPACE_ENC
eps 30
aeps 100
header 400 6100
one 400 1700
zero 400 2800
ptrail 400
post_data_bits 8
post_data 0x0
gap 6200
min_repeat 4
toggle_bit_mask 0x0
frequency 56000
begin codes
1 0x10
2 0x14
3 0x18
4 0x20
5 0x24
6 0x28
7 0x30
8 0x34
9 0x38
0 0x44
select 0x40
end codes
end remote
begin remote
name code2
bits 8
flags SPACE_ENC
eps 30
aeps 100
header 400 6100
one 400 1700
zero 400 2800
ptrail 400
post_data_bits 8
post_data 0x0
gap 6200
min_repeat 4
toggle_bit_mask 0x0
frequency 56000
begin codes
1 0x12
2 0x16
3 0x1A
4 0x22
5 0x26
6 0x2A
7 0x32
8 0x36
9 0x3A
0 0x46
select 0x42
end codes
end remote
begin remote
name code3
bits 8
flags SPACE_ENC
eps 30
aeps 100
header 400 6100
one 400 1700
zero 400 2800
ptrail 400
post_data_bits 8
post_data 0x0
gap 6200
min_repeat 4
toggle_bit_mask 0x0
frequency 56000
begin codes
1 0x11
2 0x15
3 0x19
4 0x21
5 0x25
6 0x29
7 0x31
8 0x35
9 0x39
0 0x45
Select 0x41
up 0x69
down 0x79
right 0x61
left 0x71
end codes
end remote
begin remote
name code4
bits 8
flags SPACE_ENC
eps 30
aeps 100
header 400 6100
one 400 1700
zero 400 2800
ptrail 400
post_data_bits 8
post_data 0x0
gap 6200
min_repeat 4
toggle_bit_mask 0x0
frequency 56000
begin codes
1 0x13
2 0x17
3 0x1B
4 0x23
5 0x27
6 0x2B
7 0x33
8 0x37
9 0x3B
0 0x47
select 0x43
info 0x03
power 0x0B
end codes
end remote
I am using 4 versions of the following script, one for each code#/tuner. It includes a line of code to address the audio problems with the PVR-500 and 150 cards. Change the /dev/video# to the correct value, or delete it as needed. Code: # cat /usr/local/bin/change_chan1.sh
#!/bin/bash
# Automatically Generated by /usr/local/bin/irblaster.sh
/usr/local/bin/v4l2-ctl --set-audio-input 1 -d /dev/video0 >/dev/null
echo Changing to $1
REMOTE_NAME='code1'
for digit in $(echo $1 | sed -e 's/./& /g'); do
/usr/bin/irsend --device=/dev/irblasterd SEND_ONCE $REMOTE_NAME $digit
sleep 0.7
done
Hope this helps.
Victor
_________________
Backend: Core 2-Quad CPU, 4GB RAM, 3TB
2 PVR-500, 1 HDHomerun
FE1: Zotac IONITX-B-E, w/2GB HD
FE2: Zotac MAG
|
|
| Top |
|
|
View unanswered posts
View active topics
Print view
Previous topic Next topic 
LinHES Home
Board index
FAQ
Search
Login 
Register
